On Tue, Aug 26, 2025 at 11:51:02PM +0530, Wasim Nazir wrote:
> Enhance the Qualcomm Lemans EVK board file to support essential
> peripherals and improve overall hardware capabilities, as
> outlined below:
> - Enable GPI (Generic Peripheral Interface) DMA-0/1/2 and QUPv3-0/2
> controllers to facilitate DMA and peripheral communication.
> - Add support for PCIe-0/1, including required regulators and PHYs,
> to enable high-speed external device connectivity.
> - Integrate the TCA9534 I/O expander via I2C to provide 8 additional
> GPIO lines for extended I/O functionality.
> - Enable the USB0 controller in device mode to support USB peripheral
> operations.
> - Activate remoteproc subsystems for supported DSPs such as Audio DSP,
> Compute DSP-0/1 and Generic DSP-0/1, along with their corresponding
> firmware.
> - Configure nvmem-layout on the I2C EEPROM to store data for Ethernet
> and other consumers.
> - Enable the QCA8081 2.5G Ethernet PHY on port-0 and expose the
> Ethernet MAC address via nvmem for network configuration.
> It depends on CONFIG_QCA808X_PHY to use QCA8081 PHY.
> - Add support for the Iris video decoder, including the required
> firmware, to enable video decoding capabilities.
> - Enable SD-card slot on SDHC.
>
> Co-developed-by: Viken Dadhaniya <viken.dadhaniya@xxxxxxxxxxxxxxxx>
> Signed-off-by: Viken Dadhaniya <viken.dadhaniya@xxxxxxxxxxxxxxxx>
> Co-developed-by: Sushrut Shree Trivedi <quic_sushruts@xxxxxxxxxxx>
> Signed-off-by: Sushrut Shree Trivedi <quic_sushruts@xxxxxxxxxxx>
> Co-developed-by: Nirmesh Kumar Singh <quic_nkumarsi@xxxxxxxxxxx>
> Signed-off-by: Nirmesh Kumar Singh <quic_nkumarsi@xxxxxxxxxxx>
> Co-developed-by: Krishna Kurapati <krishna.kurapati@xxxxxxxxxxxxxxxx>
> Signed-off-by: Krishna Kurapati <krishna.kurapati@xxxxxxxxxxxxxxxx>
> Co-developed-by: Mohd Ayaan Anwar <quic_mohdayaa@xxxxxxxxxxx>
> Signed-off-by: Mohd Ayaan Anwar <quic_mohdayaa@xxxxxxxxxxx>
> Co-developed-by: Dikshita Agarwal <quic_dikshita@xxxxxxxxxxx>
> Signed-off-by: Dikshita Agarwal <quic_dikshita@xxxxxxxxxxx>
> Co-developed-by: Monish Chunara <quic_mchunara@xxxxxxxxxxx>
> Signed-off-by: Monish Chunara <quic_mchunara@xxxxxxxxxxx>
> Co-developed-by: Vishal Kumar Pal <quic_vispal@xxxxxxxxxxx>
> Signed-off-by: Vishal Kumar Pal <quic_vispal@xxxxxxxxxxx>
> Signed-off-by: Wasim Nazir <wasim.nazir@xxxxxxxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/lemans-evk.dts | 387 ++++++++++++++++++++++++++++++++
> 1 file changed, 387 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/lemans-evk.dts b/arch/arm64/boot/dts/qcom/lemans-evk.dts
> index 9e415012140b..642b66c4ad1e 100644
> --- a/arch/arm64/boot/dts/qcom/lemans-evk.dts
> +++ b/arch/arm64/boot/dts/qcom/lemans-evk.dts
> @@ -16,7 +16,10 @@ / {
> compatible = "qcom,lemans-evk", "qcom,qcs9100", "qcom,sa8775p";
>
> aliases {
> + ethernet0 = ðernet0;
> + mmc1 = &sdhc;
> serial0 = &uart10;
> + serial1 = &uart17;
> };
>
> chosen {
> @@ -46,6 +49,30 @@ edp1_connector_in: endpoint {
> };
> };
> };
> +
> + vmmc_sdc: regulator-vmmc-sdc {
> + compatible = "regulator-fixed";
> + regulator-name = "vmmc_sdc";
Non-switchable, always enabled?
> +
> + regulator-min-microvolt = <2950000>;
> + regulator-max-microvolt = <2950000>;
> + };
> +
> + vreg_sdc: regulator-vreg-sdc {
> + compatible = "regulator-gpio";
> +
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2950000>;
> + regulator-name = "vreg_sdc";
> + regulator-type = "voltage";
This one also can not be disabled?
> +
> + startup-delay-us = <100>;
> +
> + gpios = <&expander1 7 GPIO_ACTIVE_HIGH>;
> +
> + states = <1800000 0x1
> + 2950000 0x0>;
> + };
> };
>
> &apps_rsc {
> @@ -277,6 +304,161 @@ vreg_l8e: ldo8 {
> };
> };
>
> +ðernet0 {
> + phy-handle = <&hsgmii_phy0>;
> + phy-mode = "2500base-x";
> +
> + pinctrl-0 = <ðernet0_default>;
> + pinctrl-names = "default";
> +
> + snps,mtl-rx-config = <&mtl_rx_setup>;
> + snps,mtl-tx-config = <&mtl_tx_setup>;
> + snps,ps-speed = <1000>;
> +
> + nvmem-cells = <&mac_addr0>;
> + nvmem-cell-names = "mac-address";
> +
> + status = "okay";
> +
> + mdio {
> + compatible = "snps,dwmac-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + hsgmii_phy0: ethernet-phy@1c {
> + compatible = "ethernet-phy-id004d.d101";
> + reg = <0x1c>;
> + reset-gpios = <&pmm8654au_2_gpios 8 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <11000>;
> + reset-deassert-us = <70000>;
> + };
> + };
> +
> + mtl_rx_setup: rx-queues-config {
> + snps,rx-queues-to-use = <4>;
> + snps,rx-sched-sp;
> +
> + queue0 {
> + snps,dcb-algorithm;
> + snps,map-to-dma-channel = <0x0>;
> + snps,route-up;
> + snps,priority = <0x1>;
> + };
> +
> + queue1 {
> + snps,dcb-algorithm;
> + snps,map-to-dma-channel = <0x1>;
> + snps,route-ptp;
> + };
> +
> + queue2 {
> + snps,avb-algorithm;
> + snps,map-to-dma-channel = <0x2>;
> + snps,route-avcp;
> + };
> +
> + queue3 {
> + snps,avb-algorithm;
> + snps,map-to-dma-channel = <0x3>;
> + snps,priority = <0xc>;
> + };
> + };
> +
> + mtl_tx_setup: tx-queues-config {
> + snps,tx-queues-to-use = <4>;
> +
> + queue0 {
> + snps,dcb-algorithm;
> + };
> +
> + queue1 {
> + snps,dcb-algorithm;
> + };
> +
> + queue2 {
> + snps,avb-algorithm;
> + snps,send_slope = <0x1000>;
> + snps,idle_slope = <0x1000>;
> + snps,high_credit = <0x3e800>;
> + snps,low_credit = <0xffc18000>;
> + };
> +
> + queue3 {
> + snps,avb-algorithm;
> + snps,send_slope = <0x1000>;
> + snps,idle_slope = <0x1000>;
> + snps,high_credit = <0x3e800>;
> + snps,low_credit = <0xffc18000>;
> + };
> + };
> +};
> +
> +&gpi_dma0 {
> + status = "okay";
> +};
> +
> +&gpi_dma1 {
> + status = "okay";
> +};
> +
> +&gpi_dma2 {
> + status = "okay";
> +};
> +
> +&i2c18 {
> + status = "okay";
> +
> + expander0: pca953x@38 {
> + compatible = "ti,tca9538";
> + #gpio-cells = <2>;
> + gpio-controller;
> + reg = <0x38>;
> + };
> +
> + expander1: pca953x@39 {
> + compatible = "ti,tca9538";
> + #gpio-cells = <2>;
> + gpio-controller;
> + reg = <0x39>;
> + };
> +
> + expander2: pca953x@3a {
> + compatible = "ti,tca9538";
> + #gpio-cells = <2>;
> + gpio-controller;
> + reg = <0x3a>;
> + };
> +
> + expander3: pca953x@3b {
> + compatible = "ti,tca9538";
> + #gpio-cells = <2>;
> + gpio-controller;
> + reg = <0x3b>;
> + };
> +
> + eeprom@50 {
> + compatible = "atmel,24c256";
> + reg = <0x50>;
> + pagesize = <64>;
> +
> + nvmem-layout {
> + compatible = "fixed-layout";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + mac_addr0: mac-addr@0 {
> + reg = <0x0 0x6>;
> + };
> + };
> + };
> +};
> +
> +&iris {
> + firmware-name = "qcom/vpu/vpu30_p4_s6.mbn";
Should it be just _s6.mbn or _s6_16mb.mbn?
> +
> + status = "okay";
> +};
> +
> &mdss0 {
> status = "okay";
> };
> @@ -323,14 +505,196 @@ &mdss0_dp1_phy {
> status = "okay";
> };
>
> +&pcie0 {
> + perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
> + wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
I think Mani has been asking lately to define these GPIOs inside the
port rather than in the host controller.
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie0_default_state>;
> +
> + status = "okay";
> +};
> +
[...]
> @@ -356,6 +720,29 @@ &ufs_mem_phy {
> status = "okay";
> };
>
> +&usb_0 {
> + status = "okay";
> +};
> +
> +&usb_0_dwc3 {
> + dr_mode = "peripheral";
Is it actually peripheral-only?
> +};
> +
--
With best wishes
Dmitry
