On Tue, Aug 26, 2025 at 11:51:02PM +0530, Wasim Nazir wrote:
Enhance the Qualcomm Lemans EVK board file to support essential
peripherals and improve overall hardware capabilities, as
outlined below:
- Enable GPI (Generic Peripheral Interface) DMA-0/1/2 and QUPv3-0/2
controllers to facilitate DMA and peripheral communication.
- Add support for PCIe-0/1, including required regulators and PHYs,
to enable high-speed external device connectivity.
- Integrate the TCA9534 I/O expander via I2C to provide 8 additional
GPIO lines for extended I/O functionality.
- Enable the USB0 controller in device mode to support USB peripheral
operations.
- Activate remoteproc subsystems for supported DSPs such as Audio DSP,
Compute DSP-0/1 and Generic DSP-0/1, along with their corresponding
firmware.
- Configure nvmem-layout on the I2C EEPROM to store data for Ethernet
and other consumers.
- Enable the QCA8081 2.5G Ethernet PHY on port-0 and expose the
Ethernet MAC address via nvmem for network configuration.
It depends on CONFIG_QCA808X_PHY to use QCA8081 PHY.
- Add support for the Iris video decoder, including the required
firmware, to enable video decoding capabilities.
- Enable SD-card slot on SDHC.
Co-developed-by: Viken Dadhaniya <viken.dadhaniya@xxxxxxxxxxxxxxxx>
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@xxxxxxxxxxxxxxxx>
Co-developed-by: Sushrut Shree Trivedi <quic_sushruts@xxxxxxxxxxx>
Signed-off-by: Sushrut Shree Trivedi <quic_sushruts@xxxxxxxxxxx>
Co-developed-by: Nirmesh Kumar Singh <quic_nkumarsi@xxxxxxxxxxx>
Signed-off-by: Nirmesh Kumar Singh <quic_nkumarsi@xxxxxxxxxxx>
Co-developed-by: Krishna Kurapati <krishna.kurapati@xxxxxxxxxxxxxxxx>
Signed-off-by: Krishna Kurapati <krishna.kurapati@xxxxxxxxxxxxxxxx>
Co-developed-by: Mohd Ayaan Anwar <quic_mohdayaa@xxxxxxxxxxx>
Signed-off-by: Mohd Ayaan Anwar <quic_mohdayaa@xxxxxxxxxxx>
Co-developed-by: Dikshita Agarwal <quic_dikshita@xxxxxxxxxxx>
Signed-off-by: Dikshita Agarwal <quic_dikshita@xxxxxxxxxxx>
Co-developed-by: Monish Chunara <quic_mchunara@xxxxxxxxxxx>
Signed-off-by: Monish Chunara <quic_mchunara@xxxxxxxxxxx>
Co-developed-by: Vishal Kumar Pal <quic_vispal@xxxxxxxxxxx>
Signed-off-by: Vishal Kumar Pal <quic_vispal@xxxxxxxxxxx>
Signed-off-by: Wasim Nazir <wasim.nazir@xxxxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/lemans-evk.dts | 387 ++++++++++++++++++++++++++++++++
1 file changed, 387 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/lemans-evk.dts b/arch/arm64/boot/dts/qcom/lemans-evk.dts
index 9e415012140b..642b66c4ad1e 100644
--- a/arch/arm64/boot/dts/qcom/lemans-evk.dts
+++ b/arch/arm64/boot/dts/qcom/lemans-evk.dts
@@ -16,7 +16,10 @@ / {
compatible = "qcom,lemans-evk", "qcom,qcs9100", "qcom,sa8775p";
aliases {
+ ethernet0 = ðernet0;
+ mmc1 = &sdhc;
serial0 = &uart10;
+ serial1 = &uart17;
};
chosen {
@@ -46,6 +49,30 @@ edp1_connector_in: endpoint {
};
};
};
+
+ vmmc_sdc: regulator-vmmc-sdc {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmc_sdc";
Non-switchable, always enabled?
+
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ vreg_sdc: regulator-vreg-sdc {
+ compatible = "regulator-gpio";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-name = "vreg_sdc";
+ regulator-type = "voltage";
This one also can not be disabled?
+
+ startup-delay-us = <100>;
+
+ gpios = <&expander1 7 GPIO_ACTIVE_HIGH>;
+
+ states = <1800000 0x1
+ 2950000 0x0>;
+ };
};
&apps_rsc {
@@ -277,6 +304,161 @@ vreg_l8e: ldo8 {
};
};
+ðernet0 {
+ phy-handle = <&hsgmii_phy0>;
+ phy-mode = "2500base-x";
+
+ pinctrl-0 = <ðernet0_default>;
+ pinctrl-names = "default";
+
+ snps,mtl-rx-config = <&mtl_rx_setup>;
+ snps,mtl-tx-config = <&mtl_tx_setup>;
+ snps,ps-speed = <1000>;
+
+ nvmem-cells = <&mac_addr0>;
+ nvmem-cell-names = "mac-address";
+
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hsgmii_phy0: ethernet-phy@1c {
+ compatible = "ethernet-phy-id004d.d101";
+ reg = <0x1c>;
+ reset-gpios = <&pmm8654au_2_gpios 8 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <11000>;
+ reset-deassert-us = <70000>;
+ };
+ };
+
+ mtl_rx_setup: rx-queues-config {
+ snps,rx-queues-to-use = <4>;
+ snps,rx-sched-sp;
+
+ queue0 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x0>;
+ snps,route-up;
+ snps,priority = <0x1>;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x1>;
+ snps,route-ptp;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x2>;
+ snps,route-avcp;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x3>;
+ snps,priority = <0xc>;
+ };
+ };
+
+ mtl_tx_setup: tx-queues-config {
+ snps,tx-queues-to-use = <4>;
+
+ queue0 {
+ snps,dcb-algorithm;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+ };
+};
+
+&gpi_dma0 {
+ status = "okay";
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&gpi_dma2 {
+ status = "okay";
+};
+
+&i2c18 {
+ status = "okay";
+
+ expander0: pca953x@38 {
+ compatible = "ti,tca9538";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x38>;
+ };
+
+ expander1: pca953x@39 {
+ compatible = "ti,tca9538";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x39>;
+ };
+
+ expander2: pca953x@3a {
+ compatible = "ti,tca9538";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x3a>;
+ };
+
+ expander3: pca953x@3b {
+ compatible = "ti,tca9538";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x3b>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c256";
+ reg = <0x50>;
+ pagesize = <64>;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ mac_addr0: mac-addr@0 {
+ reg = <0x0 0x6>;
+ };
+ };
+ };
+};
+
+&iris {
+ firmware-name = "qcom/vpu/vpu30_p4_s6.mbn";
Should it be just _s6.mbn or _s6_16mb.mbn?
+
+ status = "okay";
+};
+
&mdss0 {
status = "okay";
};
@@ -323,14 +505,196 @@ &mdss0_dp1_phy {
status = "okay";
};
+&pcie0 {
+ perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
I think Mani has been asking lately to define these GPIOs inside the
port rather than in the host controller.
