Fix endianness handling in QMI firmware transfer on big-endian
platforms. Without this fix, the firmware download fails due to
misinterpreted data structures exchanged between the host and the
wireless module.
The issue occurs during early bring-up on big endian systems, where QMI
messages are not correctly parsed by the driver, leading to failed
initialization sequences. Ensure all relevant fields are properly
converted between CPU and little-endian format in request and response
messages, as expected by the firmware. Attached logs showing the failure
before the fix:
ath12k_pci 0001:01:00.0: BAR 0: assigned [mem 0xc00000000-0xc001fffff 64bit]
ath12k_pci 0001:01:00.0: boot pci_mem 0xcd4148e9
ath12k_pci 0001:01:00.0: pci probe 17cb:1109 17cb:1109
ath12k_pci 0001:01:00.0: pci tcsr_soc_hw_version major 2 minor 0
ath12k_pci 0001:01:00.0: request MSI one vector
ath12k_pci 0001:01:00.0: MSI vectors: 1
ath12k_pci 0001:01:00.0: msi base data is 0
ath12k_pci 0001:01:00.0: Hardware name: qcn9274 hw2.0
ath12k_pci 0001:01:00.0: boot firmware request ath12k/QCN9274/hw2.0/firmware-2.bin size 15134776
ath12k_pci 0001:01:00.0: found fw timestamp 1722934582
ath12k_pci 0001:01:00.0: found m3 image ie (421880 B)
ath12k_pci 0001:01:00.0: found fw image ie (7229440 B)
ath12k_pci 0001:01:00.0: found dualmac fw image ie (7483392 B)
ath12k_pci 0001:01:00.0: found firmware features ie (1 B)
ath12k_pci 0001:01:00.0: features
ath12k_pci 0001:01:00.0: using fw api 2
ath12k_pci 0001:01:00.0: dualmac fw selected for board id: 1005
ath12k_pci 0001:01:00.0: Assign MSI to user: MHI, num_vectors: 3, user_base_data: 0, base_vector: 0
ath12k_pci 0001:01:00.0: Number of assigned MSI for MHI is 3, base vector is 0
ath12k_pci 0001:01:00.0: Assign MSI to user: CE, num_vectors: 1, user_base_data: 0, base_vector: 0
ath12k_pci 0001:01:00.0: Assign MSI to user: DP, num_vectors: 1, user_base_data: 0, base_vector: 0
ath12k_pci 0001:01:00.0: irq:18 group:0
ath12k_pci 0001:01:00.0: irq:18 group:1
ath12k_pci 0001:01:00.0: irq:18 group:2
ath12k_pci 0001:01:00.0: irq:18 group:3
ath12k_pci 0001:01:00.0: irq:18 group:4
ath12k_pci 0001:01:00.0: irq:18 group:5
ath12k_pci 0001:01:00.0: irq:18 group:6
ath12k_pci 0001:01:00.0: irq:18 group:7
ath12k_pci 0001:01:00.0: pci after request_irq msi_ep_base_data 0
ath12k_pci 0001:01:00.0: cookie:0x0
ath12k_pci 0001:01:00.0: WLAON_WARM_SW_ENTRY 0x2
ath12k_pci 0001:01:00.0: WLAON_WARM_SW_ENTRY 0x2
ath12k_pci 0001:01:00.0: soc reset cause:0
ath12k_pci 0001:01:00.0: MHISTATUS 0xff04
ath12k_pci 0001:01:00.0: pci link_ctl 0x0000 L0s 0 L1 0
ath12k_pci 0001:01:00.0: pci reg 0x3164 instance 0x11 read val 0x11
ath12k_pci 0001:01:00.0: setting mhi state: INIT(0)
ath12k_pci 0001:01:00.0: setting mhi state: POWER_ON(2)
ath12k_pci 0001:01:00.0: mhi notify status reason UNKNOWN
ath12k_pci 0001:01:00.0: mhi notify status reason MHI_CB_EE_MISSION_MODE
ath12k_pci 0001:01:00.0: qmi wifi fw qmi service connected
ath12k_pci 0001:01:00.0: phy capability resp valid 1 num_phy 2 valid 1 board_id 84934656 valid 1 single_chip_mlo_support 0
ath12k_pci 0001:01:00.0: intra device MLO is disabled hence skip QMI MLO cap
---
Changes in v2:
- Handle QMI conversion within the QMI subsystem instead of the driver.
Alexander Wilhelm (4):
soc: qcom: introduce generic QMI encoding/decoding macros
soc: qcom: fix QMI encoding/decoding for basic elements
soc: qcom: preserve CPU endianness for QMI_DATA_LEN
wifi: ath12k: enforce CPU-endian format for all QMI messages
drivers/net/wireless/ath/ath12k/qmi.c | 24 ++++++---
drivers/net/wireless/ath/ath12k/qmi.h | 16 +++---
drivers/soc/qcom/qmi_encdec.c | 74 ++++++++++++++++++++-------
3 files changed, 79 insertions(+), 35 deletions(-)
--
2.34.1
