Hi again,
On 2025-04-21 17:15:51 +0200, Niklas Söderlund wrote:
> Hi Marek,
>
> Thanks for your work!
>
> On 2025-04-20 19:36:29 +0200, Marek Vasut wrote:
> > Add Retronix R-Car V4H Sparrow Hawk board based on Renesas R-Car V4H ES3.0
> > (R8A779G3) SoC. This is a single-board computer with single gigabit ethernet,
> > DSI-to-eDP bridge, DSI and two CSI2 interfaces, audio codec, two CANFD ports,
> > micro SD card slot, USB PD supply, USB 3.0 ports, M.2 Key-M slot for NVMe SSD,
> > debug UART and JTAG.
> >
> > Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@xxxxxxxxxxx>
> > Tested-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx>
> > Signed-off-by: Marek Vasut <marek.vasut+renesas@xxxxxxxxxxx>
>
> Compared to v2 this do not boot for me. I get no console output after
> U-boot and the board appears dead.
After discussing this with you on IRC it's clear the issue was at my
side. This works as expected, please keep my T-b. Sorry for the noise.
>
> If I restore the PCIe nodes as such the boards comes back to life.
>
> ----> cut here <----
> diff --git a/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts
> index b109095a0d87..b54d45115a85 100644
> --- a/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts
> +++ b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts
> @@ -133,6 +133,13 @@ sn65dsi86_refclk: clk-x9 {
> clock-frequency = <38400000>;
> };
>
> + /* Page 26 / PCIe.0/1 CLK */
> + pcie_refclk: clk-x8 {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <25000000>;
> + };
> +
> /* Page 17 uSD-Slot */
> vcc_sdhi: regulator-vcc-sdhi {
> compatible = "regulator-gpio";
> @@ -340,6 +347,14 @@ i2c0_mux2: i2c@2 {
> reg = <2>;
> #address-cells = <1>;
> #size-cells = <0>;
> +
> + /* Page 26 / PCIe.0/1 CLK */
> + pcie_clk: clk@68 {
> + compatible = "renesas,9fgv0441";
> + reg = <0x68>;
> + clocks = <&pcie_refclk>;
> + #clock-cells = <1>;
> + };
> };
>
> i2c0_mux3: i2c@3 {
> @@ -406,20 +421,24 @@ &mmc0 {
>
> /* Page 26 / 2230 Key M M.2 */
> &pcie0_clkref {
> - clock-frequency = <100000000>;
> + status = "disabled";
> };
>
> &pciec0 {
> + clocks = <&cpg CPG_MOD 624>, <&pcie_clk 0>, <&pcie_clk 1>;
> + clock-names = "core", "ref", "aux";
> reset-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
> status = "okay";
> };
>
> /* Page 25 / PCIe to USB */
> &pcie1_clkref {
> - clock-frequency = <100000000>;
> + status = "disabled";
> };
>
> &pciec1 {
> + clocks = <&cpg CPG_MOD 625>, <&pcie_clk 2>, <&pcie_clk 3>;
> + clock-names = "core", "ref", "aux";
> /* uPD720201 is PCIe Gen2 x1 device */
> num-lanes = <1>;
> reset-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
> ----> cut here <----
>
> Is this expected?
>
> > ---
> > Cc: "Krzysztof Wilczyński" <kw@xxxxxxxxx>
> > Cc: "Rafał Miłecki" <rafal@xxxxxxxxxx>
> > Cc: Aradhya Bhatia <a-bhatia1@xxxxxx>
> > Cc: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
> > Cc: Conor Dooley <conor+dt@xxxxxxxxxx>
> > Cc: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
> > Cc: Heiko Stuebner <heiko@xxxxxxxxx>
> > Cc: Junhao Xie <bigfoot@xxxxxxxxxxx>
> > Cc: Kever Yang <kever.yang@xxxxxxxxxxxxxx>
> > Cc: Krzysztof Kozlowski <krzk+dt@xxxxxxxxxx>
> > Cc: Kuninori Morimoto <kuninori.morimoto.gx@xxxxxxxxxxx>
> > Cc: Lorenzo Pieralisi <lpieralisi@xxxxxxxxxx>
> > Cc: Magnus Damm <magnus.damm@xxxxxxxxx>
> > Cc: Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx>
> > Cc: Neil Armstrong <neil.armstrong@xxxxxxxxxx>
> > Cc: Rob Herring <robh@xxxxxxxxxx>
> > Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@xxxxxxxxxxx>
> > Cc: devicetree@xxxxxxxxxxxxxxx
> > Cc: linux-kernel@xxxxxxxxxxxxxxx
> > Cc: linux-pci@xxxxxxxxxxxxxxx
> > Cc: linux-renesas-soc@xxxxxxxxxxxxxxx
> > ---
> > V2: - Add TB from Morimoto-san
> > - Enable pwm-fan and set PWM to full by default, to achieve maximum
> > cooling effect unless configured otherwise. The blower fan is user
> > supplied device, hence this default.
> > - Add arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-fan-pwm.dtso
> > to demonstrate user supplied blower fan configuration.
> > - Add TB from Niklas
> > - Rename pins{_,-}mdio, pins{_,-}mii, scif{_,-}clk, sd{_,-}uhs
> > - Add serial1 = &hscif1; and serial2 = &hscif3
> > - Rename {Renesas,Retronix} R-Car V4H Sparrow Hawk in commit message
> > and update R-Car V4H ES3.0 to Renesas R-Car V4H ES3.0
> > V3: - Remove Renesas 9FGV0441 PCIe clock generator node from I2C bus,
> > remove clk-x8 clock node used by the PCIe clock generator, use
> > pcie0_clkref and pcie1_clkref to describe 100 MHz clock supplied
> > to both the PCIe controller and bus for now. The 9FGV0441 can and
> > does operate autonomously without any configuration. The 9FGV0441
> > description will be added in a separate follow up patch, once it
> > is clear how to describe separate controller and bus clock in DT.
> > ---
> > arch/arm64/boot/dts/renesas/Makefile | 4 +
> > .../r8a779g3-sparrow-hawk-fan-pwm.dtso | 43 ++
> > .../dts/renesas/r8a779g3-sparrow-hawk.dts | 666 ++++++++++++++++++
> > 3 files changed, 713 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-fan-pwm.dtso
> > create mode 100644 arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts
> >
> > diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
> > index d8a8d7ca4c58a..b24dddee3827c 100644
> > --- a/arch/arm64/boot/dts/renesas/Makefile
> > +++ b/arch/arm64/boot/dts/renesas/Makefile
> > @@ -94,6 +94,10 @@ dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g2-white-hawk-single.dtb
> > r8a779g2-white-hawk-single-ard-audio-da7212-dtbs := r8a779g2-white-hawk-single.dtb white-hawk-ard-audio-da7212.dtbo
> > dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g2-white-hawk-single-ard-audio-da7212.dtb
> >
> > +dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk.dtb
> > +r8a779g3-sparrow-hawk-fan-pwm-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-fan-pwm.dtbo
> > +dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-fan-pwm.dtb
> > +
> > dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-white-hawk-single.dtb
> > r8a779g3-white-hawk-single-ard-audio-da7212-dtbs := r8a779g3-white-hawk-single.dtb white-hawk-ard-audio-da7212.dtbo
> > dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-white-hawk-single-ard-audio-da7212.dtb
> > diff --git a/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-fan-pwm.dtso b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-fan-pwm.dtso
> > new file mode 100644
> > index 0000000000000..50d53c8d76c5b
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-fan-pwm.dtso
> > @@ -0,0 +1,43 @@
> > +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +/*
> > + * Device Tree Overlay for the PWM controlled blower fan in connector J3:FAN
> > + * on R-Car V4H ES3.0 Sparrow Hawk board
> > + *
> > + * Copyright (C) 2025 Marek Vasut <marek.vasut+renesas@xxxxxxxxxxx>
> > + *
> > + * Example usage:
> > + *
> > + * # Localize hwmon sysfs directory that matches the PWM fan,
> > + * # enable the PWM fan, and configure the fan speed manually.
> > + * r8a779g3-sparrow-hawk$ grep -H . /sys/class/hwmon/hwmon?/name
> > + * /sys/class/hwmon/hwmon0/name:sensor1_thermal
> > + * /sys/class/hwmon/hwmon1/name:sensor2_thermal
> > + * /sys/class/hwmon/hwmon2/name:sensor3_thermal
> > + * /sys/class/hwmon/hwmon3/name:sensor4_thermal
> > + * /sys/class/hwmon/hwmon4/name:pwmfan
> > + * ^ ^^^^^^
> > + *
> > + * # Select mode 2 , enable fan PWM and regulator and keep them enabled.
> > + * # For details, see Linux Documentation/hwmon/pwm-fan.rst
> > + * r8a779g3-sparrow-hawk$ echo 2 > /sys/class/hwmon/hwmon4/pwm1_enable
> > + *
> > + * # Configure PWM fan speed in range 0..255 , 0 is stopped , 255 is full speed .
> > + * # Fan speed 101 is about 2/5 of the PWM fan speed:
> > + * r8a779g3-sparrow-hawk$ echo 101 > /sys/class/hwmon/hwmon4/pwm1
> > + */
> > +
> > +/dts-v1/;
> > +/plugin/;
> > +
> > +/*
> > + * Override default PWM fan settings. For a list of available properties,
> > + * see schema Documentation/devicetree/bindings/hwmon/pwm-fan.yaml .
> > + */
> > +&fan {
> > + /* Available cooling levels */
> > + cooling-levels = <0 50 100 150 200 255>;
> > + /* Four pulses of tacho signal per one revolution */
> > + pulses-per-revolution = <4>;
> > + /* PWM period: 100us ~= 10 kHz */
> > + pwms = <&pwm0 0 100000>;
> > +};
> > diff --git a/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts
> > new file mode 100644
> > index 0000000000000..b109095a0d872
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts
> > @@ -0,0 +1,666 @@
> > +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +/*
> > + * Device Tree Source for the R-Car V4H ES3.0 Sparrow Hawk board
> > + *
> > + * Copyright (C) 2025 Marek Vasut <marek.vasut+renesas@xxxxxxxxxxx>
> > + */
> > +
> > +/dts-v1/;
> > +#include <dt-bindings/gpio/gpio.h>
> > +
> > +#include "r8a779g3.dtsi"
> > +
> > +/ {
> > + model = "Retronix Sparrow Hawk board based on r8a779g3";
> > + compatible = "retronix,sparrow-hawk", "renesas,r8a779g3",
> > + "renesas,r8a779g0";
> > +
> > + aliases {
> > + ethernet0 = &avb0;
> > + i2c0 = &i2c0;
> > + i2c1 = &i2c1;
> > + i2c2 = &i2c2;
> > + i2c3 = &i2c3;
> > + i2c4 = &i2c4;
> > + i2c5 = &i2c5;
> > + serial0 = &hscif0;
> > + serial1 = &hscif1;
> > + serial2 = &hscif3;
> > + spi0 = &rpc;
> > + };
> > +
> > + chosen {
> > + bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
> > + stdout-path = "serial0:921600n8";
> > + };
> > +
> > + /* Page 31 / FAN */
> > + fan: pwm-fan {
> > + pinctrl-0 = <&irq4_pins>;
> > + pinctrl-names = "default";
> > + compatible = "pwm-fan";
> > + #cooling-cells = <2>;
> > + interrupts-extended = <&intc_ex 4 IRQ_TYPE_EDGE_FALLING>;
> > + /*
> > + * The fan model connected to this device can be selected
> > + * by user. Set "cooling-levels" DT property to single 255
> > + * entry to force the fan PWM into constant HIGH, which
> > + * forces the fan to spin at maximum RPM, thus providing
> > + * maximum cooling to this device and protection against
> > + * misconfigured PWM duty cycle to the fan.
> > + *
> > + * User has to configure "pwms" and "pulses-per-revolution"
> > + * DT properties according to fan datasheet first, and then
> > + * extend "cooling-levels = <0 m n ... 255>" property to
> > + * achieve proper fan control compatible with fan model
> > + * installed by user.
> > + */
> > + cooling-levels = <255>;
> > + pulses-per-revolution = <2>;
> > + pwms = <&pwm0 0 50000>;
> > + };
> > +
> > + /*
> > + * Page 15 / LPDDR5
> > + *
> > + * This configuration listed below is for the 8 GiB board variant
> > + * with MT62F1G64D8EK-023 WT:C LPDDR5 part populated on the board.
> > + *
> > + * A variant with 16 GiB MT62F2G64D8EK-023 WT:C part populated on
> > + * the board is automatically handled by the bootloader, which
> > + * adjusts the correct DRAM size into the memory nodes below.
> > + */
> > + memory@48000000 {
> > + device_type = "memory";
> > + /* first 128MB is reserved for secure area. */
> > + reg = <0x0 0x48000000 0x0 0x78000000>;
> > + };
> > +
> > + memory@480000000 {
> > + device_type = "memory";
> > + reg = <0x4 0x80000000 0x0 0x80000000>;
> > + };
> > +
> > + memory@600000000 {
> > + device_type = "memory";
> > + reg = <0x6 0x00000000 0x1 0x00000000>;
> > + };
> > +
> > + /* Page 27 / DSI to Display */
> > + mini-dp-con {
> > + compatible = "dp-connector";
> > + label = "CN6";
> > + type = "full-size";
> > +
> > + port {
> > + mini_dp_con_in: endpoint {
> > + remote-endpoint = <&sn65dsi86_out>;
> > + };
> > + };
> > + };
> > +
> > + reg_1p2v: regulator-1p2v {
> > + compatible = "regulator-fixed";
> > + regulator-name = "fixed-1.2V";
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <1200000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + reg_1p8v: regulator-1p8v {
> > + compatible = "regulator-fixed";
> > + regulator-name = "fixed-1.8V";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + reg_3p3v: regulator-3p3v {
> > + compatible = "regulator-fixed";
> > + regulator-name = "fixed-3.3V";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + /* Page 27 / DSI to Display */
> > + sn65dsi86_refclk: clk-x9 {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <38400000>;
> > + };
> > +
> > + /* Page 17 uSD-Slot */
> > + vcc_sdhi: regulator-vcc-sdhi {
> > + compatible = "regulator-gpio";
> > + regulator-name = "SDHI VccQ";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + gpios = <&gpio8 13 GPIO_ACTIVE_HIGH>;
> > + gpios-states = <1>;
> > + states = <3300000 0>, <1800000 1>;
> > + };
> > +};
> > +
> > +/* Page 22 / Ether_AVB0 */
> > +&avb0 {
> > + pinctrl-0 = <&avb0_pins>;
> > + pinctrl-names = "default";
> > + phy-handle = <&avb0_phy>;
> > + tx-internal-delay-ps = <2000>;
> > + status = "okay";
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + avb0_phy: ethernet-phy@0 { /* KSZ9031RNXVB */
> > + compatible = "ethernet-phy-id0022.1622",
> > + "ethernet-phy-ieee802.3-c22";
> > + rxc-skew-ps = <1500>;
> > + reg = <0>;
> > + /* AVB0_PHY_INT_V */
> > + interrupts-extended = <&gpio7 5 IRQ_TYPE_LEVEL_LOW>;
> > + /* GP7_10/AVB0_RESETN_V */
> > + reset-gpios = <&gpio7 10 GPIO_ACTIVE_LOW>;
> > + reset-assert-us = <10000>;
> > + reset-deassert-us = <300>;
> > + };
> > + };
> > +};
> > +
> > +/* Page 28 / CANFD_IF */
> > +&can_clk {
> > + clock-frequency = <40000000>;
> > +};
> > +
> > +/* Page 28 / CANFD_IF */
> > +&canfd {
> > + pinctrl-0 = <&canfd3_pins>, <&canfd4_pins>, <&can_clk_pins>;
> > + pinctrl-names = "default";
> > +
> > + status = "okay";
> > +
> > + channel3 {
> > + status = "okay";
> > + };
> > +
> > + channel4 {
> > + status = "okay";
> > + };
> > +};
> > +
> > +/* Page 27 / DSI to Display */
> > +&dsi1 {
> > + status = "okay";
> > +
> > + ports {
> > + port@1 {
> > + dsi1_out: endpoint {
> > + remote-endpoint = <&sn65dsi86_in>;
> > + data-lanes = <1 2 3 4>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +/* Page 27 / DSI to Display */
> > +&du {
> > + status = "okay";
> > +};
> > +
> > +/* Page 5 / R-Car V4H_INT_I2C */
> > +&extal_clk { /* X3 */
> > + clock-frequency = <16666666>;
> > +};
> > +
> > +/* Page 5 / R-Car V4H_INT_I2C */
> > +&extalr_clk { /* X2 */
> > + clock-frequency = <32768>;
> > +};
> > +
> > +/* Page 26 / 2230 Key M M.2 */
> > +&gpio4 {
> > + /* 9FGV0441 nOE inputs 0 and 1 */
> > + pcie-m2-oe-hog {
> > + gpio-hog;
> > + gpios = <21 GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + line-name = "PCIe-CLK-nOE-M2";
> > + };
> > +
> > + /* 9FGV0441 nOE inputs 2 and 3 */
> > + pcie-usb-oe-hog {
> > + gpio-hog;
> > + gpios = <22 GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + line-name = "PCIe-CLK-nOE-USB";
> > + };
> > +};
> > +
> > +/* Page 23 / DEBUG */
> > +&hscif0 { /* FTDI ADBUS[3:0] */
> > + pinctrl-0 = <&hscif0_pins>;
> > + pinctrl-names = "default";
> > + uart-has-rtscts;
> > + bootph-all;
> > +
> > + status = "okay";
> > +};
> > +
> > +/* Page 23 / DEBUG */
> > +&hscif1 { /* FTDI BDBUS[3:0] */
> > + pinctrl-0 = <&hscif1_pins>;
> > + pinctrl-names = "default";
> > + uart-has-rtscts;
> > +
> > + status = "okay";
> > +};
> > +
> > +/* Page 24 / UART */
> > +&hscif3 { /* CN7 pins 8 (TX) and 10 (RX) */
> > + pinctrl-0 = <&hscif3_pins>;
> > + pinctrl-names = "default";
> > +
> > + status = "okay";
> > +};
> > +
> > +/* Page 24 / I2C SWITCH */
> > +&i2c0 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + pinctrl-0 = <&i2c0_pins>;
> > + pinctrl-names = "default";
> > + clock-frequency = <400000>;
> > + status = "okay";
> > +
> > + mux@71 {
> > + compatible = "nxp,pca9544"; /* TCA9544 */
> > + reg = <0x71>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + vdd-supply = <®_3p3v>;
> > +
> > + i2c0_mux0: i2c@0 {
> > + reg = <0>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + /* Page 27 / DSI to Display */
> > + bridge@2c {
> > + pinctrl-0 = <&irq0_pins>;
> > + pinctrl-names = "default";
> > +
> > + compatible = "ti,sn65dsi86";
> > + reg = <0x2c>;
> > +
> > + clocks = <&sn65dsi86_refclk>;
> > + clock-names = "refclk";
> > +
> > + interrupts-extended = <&intc_ex 0 IRQ_TYPE_LEVEL_HIGH>;
> > +
> > + enable-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
> > +
> > + vccio-supply = <®_1p8v>;
> > + vpll-supply = <®_1p8v>;
> > + vcca-supply = <®_1p2v>;
> > + vcc-supply = <®_1p2v>;
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + sn65dsi86_in: endpoint {
> > + remote-endpoint = <&dsi1_out>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <1>;
> > + sn65dsi86_out: endpoint {
> > + remote-endpoint = <&mini_dp_con_in>;
> > + };
> > + };
> > + };
> > + };
> > + };
> > +
> > + i2c0_mux1: i2c@1 {
> > + reg = <1>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + };
> > +
> > + i2c0_mux2: i2c@2 {
> > + reg = <2>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + };
> > +
> > + i2c0_mux3: i2c@3 {
> > + reg = <3>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + };
> > + };
> > +};
> > +
> > +/* Page 29 / CSI_IF_CN / CAM_CN0 */
> > +&i2c1 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + pinctrl-0 = <&i2c1_pins>;
> > + pinctrl-names = "default";
> > +};
> > +
> > +/* Page 29 / CSI_IF_CN / CAM_CN1 */
> > +&i2c2 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + pinctrl-0 = <&i2c2_pins>;
> > + pinctrl-names = "default";
> > +};
> > +
> > +/* Page 31 / IO_CN */
> > +&i2c3 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + pinctrl-0 = <&i2c3_pins>;
> > + pinctrl-names = "default";
> > +};
> > +
> > +/* Page 31 / IO_CN */
> > +&i2c4 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + pinctrl-0 = <&i2c4_pins>;
> > + pinctrl-names = "default";
> > +};
> > +
> > +/* Page 18 / POWER_CORE and Page 19 / POWER_PMIC */
> > +&i2c5 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + pinctrl-0 = <&i2c5_pins>;
> > + pinctrl-names = "default";
> > +};
> > +
> > +/* Page 17 uSD-Slot */
> > +&mmc0 {
> > + pinctrl-0 = <&sd_pins>;
> > + pinctrl-1 = <&sd_uhs_pins>;
> > + pinctrl-names = "default", "state_uhs";
> > + bus-width = <4>;
> > + cd-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>; /* SD_CD */
> > + sd-uhs-sdr50;
> > + sd-uhs-sdr104;
> > + vmmc-supply = <®_3p3v>;
> > + vqmmc-supply = <&vcc_sdhi>;
> > + status = "okay";
> > +};
> > +
> > +/* Page 26 / 2230 Key M M.2 */
> > +&pcie0_clkref {
> > + clock-frequency = <100000000>;
> > +};
> > +
> > +&pciec0 {
> > + reset-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
> > + status = "okay";
> > +};
> > +
> > +/* Page 25 / PCIe to USB */
> > +&pcie1_clkref {
> > + clock-frequency = <100000000>;
> > +};
> > +
> > +&pciec1 {
> > + /* uPD720201 is PCIe Gen2 x1 device */
> > + num-lanes = <1>;
> > + reset-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
> > + status = "okay";
> > +};
> > +
> > +&pfc {
> > + pinctrl-0 = <&scif_clk_pins>;
> > + pinctrl-names = "default";
> > +
> > + /* Page 22 / Ether_AVB0 */
> > + avb0_pins: avb0 {
> > + mux {
> > + groups = "avb0_link", "avb0_mdio", "avb0_rgmii",
> > + "avb0_txcrefclk";
> > + function = "avb0";
> > + };
> > +
> > + pins-mdio {
> > + groups = "avb0_mdio";
> > + drive-strength = <21>;
> > + };
> > +
> > + pins-mii {
> > + groups = "avb0_rgmii";
> > + drive-strength = <21>;
> > + };
> > +
> > + };
> > +
> > + /* Page 28 / CANFD_IF */
> > + can_clk_pins: can-clk {
> > + groups = "can_clk";
> > + function = "can_clk";
> > + };
> > +
> > + /* Page 28 / CANFD_IF */
> > + canfd3_pins: canfd3 {
> > + groups = "canfd3_data";
> > + function = "canfd3";
> > + };
> > +
> > + /* Page 28 / CANFD_IF */
> > + canfd4_pins: canfd4 {
> > + groups = "canfd4_data";
> > + function = "canfd4";
> > + };
> > +
> > + /* Page 23 / DEBUG */
> > + hscif0_pins: hscif0 {
> > + groups = "hscif0_data", "hscif0_ctrl";
> > + function = "hscif0";
> > + };
> > +
> > + /* Page 23 / DEBUG */
> > + hscif1_pins: hscif1 {
> > + groups = "hscif1_data_a", "hscif1_ctrl_a";
> > + function = "hscif1";
> > + };
> > +
> > + /* Page 24 / UART */
> > + hscif3_pins: hscif3 {
> > + groups = "hscif3_data_a";
> > + function = "hscif3";
> > + };
> > +
> > + /* Page 24 / I2C SWITCH */
> > + i2c0_pins: i2c0 {
> > + groups = "i2c0";
> > + function = "i2c0";
> > + };
> > +
> > + /* Page 29 / CSI_IF_CN / CAM_CN0 */
> > + i2c1_pins: i2c1 {
> > + groups = "i2c1";
> > + function = "i2c1";
> > + };
> > +
> > + /* Page 29 / CSI_IF_CN / CAM_CN1 */
> > + i2c2_pins: i2c2 {
> > + groups = "i2c2";
> > + function = "i2c2";
> > + };
> > +
> > + /* Page 31 / IO_CN */
> > + i2c3_pins: i2c3 {
> > + groups = "i2c3";
> > + function = "i2c3";
> > + };
> > +
> > + /* Page 31 / IO_CN */
> > + i2c4_pins: i2c4 {
> > + groups = "i2c4";
> > + function = "i2c4";
> > + };
> > +
> > + /* Page 18 / POWER_CORE */
> > + i2c5_pins: i2c5 {
> > + groups = "i2c5";
> > + function = "i2c5";
> > + };
> > +
> > + /* Page 27 / DSI to Display */
> > + irq0_pins: irq0 {
> > + groups = "intc_ex_irq0_a";
> > + function = "intc_ex";
> > + };
> > +
> > + /* Page 31 / FAN */
> > + irq4_pins: irq4 {
> > + groups = "intc_ex_irq4_b";
> > + function = "intc_ex";
> > + };
> > +
> > + /* Page 31 / FAN */
> > + pwm0_pins: pwm0 {
> > + groups = "pwm0";
> > + function = "pwm0";
> > + };
> > +
> > + /* Page 31 / CN7 pin 12 */
> > + pwm1_pins: pwm1 {
> > + groups = "pwm1_b";
> > + function = "pwm1";
> > + };
> > +
> > + /* Page 31 / CN7 pin 32 */
> > + pwm6_pins: pwm6 {
> > + groups = "pwm6";
> > + function = "pwm6";
> > + };
> > +
> > + /* Page 31 / CN7 pin 33 */
> > + pwm7_pins: pwm7 {
> > + groups = "pwm7";
> > + function = "pwm7";
> > + };
> > +
> > + /* Page 16 / QSPI_FLASH */
> > + qspi0_pins: qspi0 {
> > + groups = "qspi0_ctrl", "qspi0_data4";
> > + function = "qspi0";
> > + bootph-all;
> > + };
> > +
> > + /* Page 6 / SCIF_CLK_SOC_V */
> > + scif_clk_pins: scif-clk {
> > + groups = "scif_clk";
> > + function = "scif_clk";
> > + };
> > +
> > + /* Page 17 uSD-Slot */
> > + sd_pins: sd {
> > + groups = "mmc_data4", "mmc_ctrl";
> > + function = "mmc";
> > + power-source = <3300>;
> > + };
> > +
> > + /* Page 17 uSD-Slot */
> > + sd_uhs_pins: sd-uhs {
> > + groups = "mmc_data4", "mmc_ctrl";
> > + function = "mmc";
> > + power-source = <1800>;
> > + };
> > +};
> > +
> > +/* Page 31 / FAN */
> > +&pwm0 {
> > + pinctrl-0 = <&pwm0_pins>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > +};
> > +
> > +/* Page 31 / CN7 pin 12 */
> > +&pwm1 {
> > + pinctrl-0 = <&pwm1_pins>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > +};
> > +
> > +/* Page 31 / CN7 pin 32 */
> > +&pwm6 {
> > + pinctrl-0 = <&pwm6_pins>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > +};
> > +
> > +/* Page 31 / CN7 pin 33 */
> > +&pwm7 {
> > + pinctrl-0 = <&pwm7_pins>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > +};
> > +
> > +/* Page 16 / QSPI_FLASH */
> > +&rpc {
> > + pinctrl-0 = <&qspi0_pins>;
> > + pinctrl-names = "default";
> > + bootph-all;
> > +
> > + status = "okay";
> > +
> > + flash@0 {
> > + compatible = "spansion,s25fs512s", "jedec,spi-nor";
> > + reg = <0>;
> > + spi-max-frequency = <40000000>;
> > + spi-rx-bus-width = <4>;
> > + spi-tx-bus-width = <4>;
> > + bootph-all;
> > +
> > + partitions {
> > + compatible = "fixed-partitions";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + boot@0 {
> > + reg = <0x0 0x1000000>;
> > + read-only;
> > + };
> > +
> > + user@1000000 {
> > + reg = <0x1000000 0x2f80000>;
> > + };
> > +
> > + env1@3f80000 {
> > + reg = <0x3f80000 0x40000>;
> > + };
> > +
> > + env2@3fc0000 {
> > + reg = <0x3fc0000 0x40000>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&rwdt {
> > + timeout-sec = <60>;
> > + status = "okay";
> > +};
> > +
> > +/* Page 6 / SCIF_CLK_SOC_V */
> > +&scif_clk { /* X12 */
> > + clock-frequency = <24000000>;
> > +};
> > --
> > 2.47.2
> >
>
> --
> Kind Regards,
> Niklas Söderlund
--
Kind Regards,
Niklas Söderlund
