On 8/13/25 9:52 PM, Yao Zi wrote:
On Wed, Aug 13, 2025 at 01:46:55PM -0500, Alex Elder wrote:
Add the Device Tree binding for the PCIe/USB 3.0 combo PHY found in
the SpacemiT K1 SoC. This is one of three PCIe PHYs, and is unusual
in that only the combo PHY can perform a calibration step needed to
determine settings used by the other two PCIe PHYs.
Calibration must be done with the combo PHY in PCIe mode, and to allow
this to occur independent of the eventual use for the PHY (PCIe or USB)
some PCIe-related properties must be supplied: clocks; resets; and a
syscon phandle.
Signed-off-by: Alex Elder <elder@xxxxxxxxxxxx>
---
.../bindings/phy/spacemit,k1-combo-phy.yaml | 110 ++++++++++++++++++
1 file changed, 110 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/spacemit,k1-combo-phy.yaml
diff --git a/Documentation/devicetree/bindings/phy/spacemit,k1-combo-phy.yaml b/Documentation/devicetree/bindings/phy/spacemit,k1-combo-phy.yaml
new file mode 100644
index 0000000000000..ed78083a53231
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/spacemit,k1-combo-phy.yaml
...
+ spacemit,syscon-pmu:
+ description:
+ PHandle that refers to the APMU system controller, whose
+ regmap is used in setting the mode
+ $ref: /schemas/types.yaml#/definitions/phandle
Clock controllers and ethernet controllers all use spacemit,apmu to
refer the APMU system controller. Do you think it's better to keep them
aligned?
I do think it's better to keep them aligned.
And I appreciate your noticing this. I don't see anything
that's accepted upstream that defines properties like this,
but I now see this:
https://lore.kernel.org/lkml/20250812-net-k1-emac-v5-2-dd17c4905f49@xxxxxxxxxxx/
I did a quick scan for what others do when a property's
value is a phandle, and other than just "syscon" it seems
that word is omitted.
So unless someone else suggests otherwise, I'll use
"spacemit,apmu" for this property in my next version.
...
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/spacemit,k1-syscon.h>
+ combo_phy: phy@c0b10000 {
This label is unnecessary.
OK. I used it when testing USB but we can add the label
back when that driver gets reviewed.
+ compatible = "spacemit,k1-combo-phy";
+ reg = <0xc0b10000 0x1000>;
+ clocks = <&syscon_apmu CLK_PCIE0_DBI>,
+ <&syscon_apmu CLK_PCIE0_MASTER>,
+ <&syscon_apmu CLK_PCIE0_SLAVE>;
+ clock-names = "dbi",
+ "mstr",
+ "slv";
+ resets = <&syscon_apmu RESET_PCIE0_DBI>,
+ <&syscon_apmu RESET_PCIE0_MASTER>,
+ <&syscon_apmu RESET_PCIE0_SLAVE>,
+ <&syscon_apmu RESET_PCIE0_GLOBAL>;
+ reset-names = "dbi",
+ "mstr",
+ "slv",
+ "global";
+ spacemit,syscon-pmu = <&syscon_apmu>;
+ #phy-cells = <1>;
+ status = "disabled";
+ };
Best regards,
Yao Zi
Thanks a lot.
-Alex
