On 8/29/25 7:45 PM, Marcelo Schmitt wrote:
> Set AD4030 series device to do two data bit transitions per clock cycle per
> active lane when specified by firmware. The dual data rate (DDR) feature is
> available only for host clock mode and echo clock mode.
>
> Co-developed-by: Sergiu Cuciurean <sergiu.cuciurean@xxxxxxxxxx>
> Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@xxxxxxxxxx>
> Signed-off-by: Marcelo Schmitt <marcelo.schmitt@xxxxxxxxxx>
> ---
> drivers/iio/adc/ad4030.c | 11 +++++++++++
> 1 file changed, 11 insertions(+)
>
> diff --git a/drivers/iio/adc/ad4030.c b/drivers/iio/adc/ad4030.c
> index a5931056936a..37ba00097efe 100644
> --- a/drivers/iio/adc/ad4030.c
> +++ b/drivers/iio/adc/ad4030.c
> @@ -74,6 +74,7 @@
> (AD4030_REG_GAIN_X0_MSB + (AD4030_REG_GAIN_BYTES_NB * (ch)))
> #define AD4030_REG_MODES 0x20
> #define AD4030_REG_MODES_MASK_OUT_DATA_MODE GENMASK(2, 0)
> +#define AD4030_REG_MODES_MASK_DDR_MODE BIT(3)
> #define AD4030_REG_MODES_MASK_CLOCK_MODE GENMASK(5, 4)
> #define AD4030_REG_MODES_MASK_LANE_MODE GENMASK(7, 6)
> #define AD4030_REG_OSCILATOR 0x21
> @@ -175,6 +176,7 @@ struct ad4030_state {
> enum ad4030_out_mode mode;
> enum ad4030_lane_mode lane_mode;
> enum ad4030_clock_mode clock_mode;
> + bool ddr;
> /* offload sampling spi message */
> struct spi_transfer offload_xfer;
> struct spi_message offload_msg;
> @@ -1218,6 +1220,9 @@ static void ad4030_prepare_offload_msg(struct ad4030_state *st)
> else
> offload_bpw = data_width / (1 << st->lane_mode);
>
> + if (st->ddr)
> + offload_bpw /= 2;
> +
There is already an existing dtr_mode flag in struct spi_transfer. We should
be using that instead of providing an inaccurate bits per word value.
> st->offload_xfer.speed_hz = AD4030_SPI_MAX_REG_XFER_SPEED;
> st->offload_xfer.bits_per_word = offload_bpw;
> st->offload_xfer.len = roundup_pow_of_two(BITS_TO_BYTES(offload_bpw));
> @@ -1271,6 +1276,12 @@ static int ad4030_config(struct ad4030_state *st)
> reg_modes |= FIELD_PREP(AD4030_REG_MODES_MASK_CLOCK_MODE,
> ret >= 0 ? ret : AD4030_SPI_CLOCK_MODE);
>
> + /* DDR is only valid for echo clock and host clock modes */
> + if (ret == AD4030_ECHO_CLOCK_MODE || ret == AD4030_CLOCK_HOST_MODE) {
> + st->ddr = device_property_read_bool(dev, "adi,dual-data-rate");
As mentioned in the dt-bindings patch review, we can already get this info
from the spi controller via dtr_caps.
> + reg_modes |= FIELD_PREP(AD4030_REG_MODES_MASK_DDR_MODE, st->ddr);
> + }
> +
> ret = regmap_write(st->regmap, AD4030_REG_MODES, reg_modes);
> if (ret)
> return ret;
We will need a separate patch to add support for dtr_caps and dtr_mode to the
axi-spi-engine driver. And likely some HDL work for that as well. So I would
suggest splitting this out into a separate series.
