Re: [PATCH 2/5] arm64: dts: qcom: lemans: Add SDHC controller and SDC pin configuration

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 8/27/25 3:20 AM, Dmitry Baryshkov wrote:
> On Tue, Aug 26, 2025 at 11:51:01PM +0530, Wasim Nazir wrote:
>> From: Monish Chunara <quic_mchunara@xxxxxxxxxxx>
>>
>> Introduce the SDHC v5 controller node for the Lemans platform.
>> This controller supports either eMMC or SD-card, but only one
>> can be active at a time. SD-card is the preferred configuration
>> on Lemans targets, so describe this controller.
>>
>> Define the SDC interface pins including clk, cmd, and data lines
>> to enable proper communication with the SDHC controller.
>>
>> Signed-off-by: Monish Chunara <quic_mchunara@xxxxxxxxxxx>
>> Co-developed-by: Wasim Nazir <wasim.nazir@xxxxxxxxxxxxxxxx>
>> Signed-off-by: Wasim Nazir <wasim.nazir@xxxxxxxxxxxxxxxx>
>> ---
>>  arch/arm64/boot/dts/qcom/lemans.dtsi | 70 ++++++++++++++++++++++++++++++++++++
>>  1 file changed, 70 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/lemans.dtsi b/arch/arm64/boot/dts/qcom/lemans.dtsi
>> index 99a566b42ef2..a5a3cdba47f3 100644
>> --- a/arch/arm64/boot/dts/qcom/lemans.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/lemans.dtsi
>> @@ -3834,6 +3834,36 @@ apss_tpdm2_out: endpoint {
>>  			};
>>  		};
>>  
>> +		sdhc: mmc@87c4000 {
>> +			compatible = "qcom,sa8775p-sdhci", "qcom,sdhci-msm-v5";
>> +			reg = <0x0 0x087c4000 0x0 0x1000>;
>> +
>> +			interrupts = <GIC_SPI 383 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 521 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "hc_irq", "pwr_irq";
>> +
>> +			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
>> +				 <&gcc GCC_SDCC1_APPS_CLK>;
>> +			clock-names = "iface", "core";
>> +
>> +			interconnects = <&aggre1_noc MASTER_SDC 0 &mc_virt SLAVE_EBI1 0>,
>> +					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDC1 0>;
>> +			interconnect-names = "sdhc-ddr", "cpu-sdhc";
>> +
>> +			iommus = <&apps_smmu 0x0 0x0>;
>> +			dma-coherent;
>> +
>> +			resets = <&gcc GCC_SDCC1_BCR>;
>> +
>> +			no-sdio;
>> +			no-mmc;
>> +			bus-width = <4>;
> 
> This is the board configuration, it should be defined in the EVK DTS.

Unless the controller is actually incapable of doing non-SDCards

But from the limited information I can find, this one should be able
to do both

Konrad




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux