> > > > On 6/16/25 2:38 PM, Patrick Dupre via users wrote: > > >> > > >> On 6/16/25 2:11 PM, Patrick Dupre via users wrote: > > >>> OK, > > >>> > > >>> Now it is working with > > >>> Kernel IP routing table > > >>> Destination Gateway Genmask Flags MSS Window irtt Iface > > >>> 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 enp0s20f0u11 > > >>> 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 bridge0 > > >>> 10.40.0.0 0.0.0.0 255.255.255.0 U 0 0 0 bridge0 > > >>> 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 enp0s20f0u11 > > >>> 192.168.1.1 0.0.0.0 255.255.255.255 UH 0 0 0 bridge0 > > >>> 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 > > >>> > > >>> Question > > >>> I have enp1s0 ipv4 manually set as > > >>> 10.40.1.0/24 without GW, neither DNS > > >>> enp2s0 ivpv4 also manually set as > > >>> 10.40.2.0/24 without GW, neither DNS > > >> > > >> These should both be unconfigured. They are part of the bridge. > > >> And I'm still concerned that 192.168.1.1 is on the bridge. > > > > > > It is configured in automatic DHCP > > > enp0s20f0u11: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 > > > inet 192.168.1.166 netmask 255.255.255.0 broadcast 192.168.1.255 > > > inet6 fe80::a594:2280:6476:1293 prefixlen 64 scopeid 0x20<link> > > > ether 96:bd:e2:d4:3e:52 txqueuelen 1000 (Ethernet) > > > > > > > > > Should it be set manually? > > > > That is the USB port. It should not be part of the bridge. > > > > >> > > >>> and > > >>> enp1s0 port 1 and enp2s0 port 2 set automatic DHCP > > >>> Should I keep it like that? > > >>> Will be the IP addresses always conserved? > > >> > > >> I don't know what you mean by this. I would recommend that PC B and C > > >> have static addresses. I don't think the DHCP reservations are preserved. > > > They are static > > > The only static ones are bridge0 port1 and port2 > > > and > > > USB Ethernet (enp0s20f0u11) > > > > I don't understand what you mean about the ports. Whatever those are, > > they shouldn't be configured. > > Maybe, but I dod not configure any thing on that side. > It is done automatically by fedora > The only option that I se is to disable the interface !!! > > PC B and PC C being not running, I have > Kernel IP routing table > Destination Gateway Genmask Flags MSS Window irtt Iface > 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 enp0s20f0u11 > 10.42.0.0 0.0.0.0 255.255.255.0 U 0 0 0 bridge0 > 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 enp0s20f0u11 > 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 > > But with this configuration, the local network does not work. Probably because the bridge port is set in 10.42.0.0 (Automatic DHCP) and not in 10.40.0.0. If it is correct, I need to set it static 10.40.0.0 255.255.255.0 what about the Gateway and the DNS ? Note also that the IP address of enp0s20f0u11 (USB Ethernet) has also changed. Should I set it static ? 192.168.1.166/24 Gateway 192.168.1.1 ? DNS 192.168.1.1 ? Thanks -- _______________________________________________ users mailing list -- users@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to users-leave@xxxxxxxxxxxxxxxxxxxxxxx Fedora Code of Conduct: https://docs.fedoraproject.org/en-US/project/code-of-conduct/ List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines List Archives: https://lists.fedoraproject.org/archives/list/users@xxxxxxxxxxxxxxxxxxxxxxx Do not reply to spam, report it: https://pagure.io/fedora-infrastructure/new_issue
