Clear some bits in some registers in order to allow RTL8851BU to power
on. This is done both when powering on and when powering off because
that's what the vendor driver does.
Also tested with RTL8832BU and RTL8832CU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@xxxxxxxxx>
---
v2:
- Put the new code in a function.
v3:
- Delete empty line.
- Add more information to the commit message.
---
drivers/net/wireless/realtek/rtw89/mac.c | 19 +++++++++++++++++++
drivers/net/wireless/realtek/rtw89/reg.h | 1 +
2 files changed, 20 insertions(+)
diff --git a/drivers/net/wireless/realtek/rtw89/mac.c b/drivers/net/wireless/realtek/rtw89/mac.c
index c018071c94ee..96c54d1c658e 100644
--- a/drivers/net/wireless/realtek/rtw89/mac.c
+++ b/drivers/net/wireless/realtek/rtw89/mac.c
@@ -1440,6 +1440,23 @@ void rtw89_mac_notify_wake(struct rtw89_dev *rtwdev)
rtw89_mac_send_rpwm(rtwdev, state, true);
}
+static void rtw89_mac_power_switch_boot_mode(struct rtw89_dev *rtwdev)
+{
+ u32 boot_mode;
+
+ if (rtwdev->hci.type != RTW89_HCI_TYPE_USB)
+ return;
+
+ boot_mode = rtw89_read32_mask(rtwdev, R_AX_GPIO_MUXCFG, B_AX_BOOT_MODE);
+ if (!boot_mode)
+ return;
+
+ rtw89_write32_clr(rtwdev, R_AX_SYS_PW_CTRL, B_AX_APFN_ONMAC);
+ rtw89_write32_clr(rtwdev, R_AX_SYS_STATUS1, B_AX_AUTO_WLPON);
+ rtw89_write32_clr(rtwdev, R_AX_GPIO_MUXCFG, B_AX_BOOT_MODE);
+ rtw89_write32_clr(rtwdev, R_AX_RSV_CTRL, B_AX_R_DIS_PRST);
+}
+
static int rtw89_mac_power_switch(struct rtw89_dev *rtwdev, bool on)
{
#define PWR_ACT 1
@@ -1450,6 +1467,8 @@ static int rtw89_mac_power_switch(struct rtw89_dev *rtwdev, bool on)
int ret;
u8 val;
+ rtw89_mac_power_switch_boot_mode(rtwdev);
+
if (on) {
cfg_seq = chip->pwr_on_seq;
cfg_func = chip->ops->pwr_on_func;
diff --git a/drivers/net/wireless/realtek/rtw89/reg.h b/drivers/net/wireless/realtek/rtw89/reg.h
index c680441232fb..be4a8486c9f8 100644
--- a/drivers/net/wireless/realtek/rtw89/reg.h
+++ b/drivers/net/wireless/realtek/rtw89/reg.h
@@ -183,6 +183,7 @@
#define R_AX_SYS_STATUS1 0x00F4
#define B_AX_SEL_0XC0_MASK GENMASK(17, 16)
+#define B_AX_AUTO_WLPON BIT(10)
#define B_AX_PAD_HCI_SEL_V2_MASK GENMASK(5, 3)
#define MAC_AX_HCI_SEL_SDIO_UART 0
#define MAC_AX_HCI_SEL_MULTI_USB 1
--
2.49.0
