Clear some bits in some registers in order to allow RTL8851BU to power
on. Also tested with RTL8832BU and RTL8832CU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@xxxxxxxxx>
---
v2:
- Put the new code in a function.
---
drivers/net/wireless/realtek/rtw89/mac.c | 20 ++++++++++++++++++++
drivers/net/wireless/realtek/rtw89/reg.h | 1 +
2 files changed, 21 insertions(+)
diff --git a/drivers/net/wireless/realtek/rtw89/mac.c b/drivers/net/wireless/realtek/rtw89/mac.c
index 875c1a3c5ca8..bccb504915f4 100644
--- a/drivers/net/wireless/realtek/rtw89/mac.c
+++ b/drivers/net/wireless/realtek/rtw89/mac.c
@@ -1449,6 +1449,24 @@ void rtw89_mac_notify_wake(struct rtw89_dev *rtwdev)
rtw89_mac_send_rpwm(rtwdev, state, true);
}
+static void rtw89_mac_power_switch_boot_mode(struct rtw89_dev *rtwdev)
+{
+ u32 boot_mode;
+
+ if (rtwdev->hci.type != RTW89_HCI_TYPE_USB)
+ return;
+
+ boot_mode = rtw89_read32_mask(rtwdev, R_AX_GPIO_MUXCFG, B_AX_BOOT_MODE);
+
+ if (!boot_mode)
+ return;
+
+ rtw89_write32_clr(rtwdev, R_AX_SYS_PW_CTRL, B_AX_APFN_ONMAC);
+ rtw89_write32_clr(rtwdev, R_AX_SYS_STATUS1, B_AX_AUTO_WLPON);
+ rtw89_write32_clr(rtwdev, R_AX_GPIO_MUXCFG, B_AX_BOOT_MODE);
+ rtw89_write32_clr(rtwdev, R_AX_RSV_CTRL, B_AX_R_DIS_PRST);
+}
+
static int rtw89_mac_power_switch(struct rtw89_dev *rtwdev, bool on)
{
#define PWR_ACT 1
@@ -1459,6 +1477,8 @@ static int rtw89_mac_power_switch(struct rtw89_dev *rtwdev, bool on)
int ret;
u8 val;
+ rtw89_mac_power_switch_boot_mode(rtwdev);
+
if (on) {
cfg_seq = chip->pwr_on_seq;
cfg_func = chip->ops->pwr_on_func;
diff --git a/drivers/net/wireless/realtek/rtw89/reg.h b/drivers/net/wireless/realtek/rtw89/reg.h
index f05c81ae5869..9d9e1b02bfc7 100644
--- a/drivers/net/wireless/realtek/rtw89/reg.h
+++ b/drivers/net/wireless/realtek/rtw89/reg.h
@@ -182,6 +182,7 @@
#define R_AX_SYS_STATUS1 0x00F4
#define B_AX_SEL_0XC0_MASK GENMASK(17, 16)
+#define B_AX_AUTO_WLPON BIT(10)
#define B_AX_PAD_HCI_SEL_V2_MASK GENMASK(5, 3)
#define MAC_AX_HCI_SEL_SDIO_UART 0
#define MAC_AX_HCI_SEL_MULTI_USB 1
--
2.49.0
