On Mon Apr 21, 2025 at 1:47 PM CEST, Karthikeyan Kathirvel wrote:
> Install beacon protection keys in hardware for AP modes only if hardware
> supports it, as indicated by the WMI service bit
> WMI_TLV_SERVICE_BEACON_PROTECTION_SUPPORT. Allow keyidx up to 7, since
> beacon protection uses keyidx 6 and 7.
>
> Control this feature by setting bit 0 of feature_enable_bitmap when sending
> the WMI_BCN_TMPL_CMDID command to firmware.
>
> Check for the beacon protection enabled bit in both tx and non-tx profiles
> for MBSSID cases. If set in either profile, enable the beacon protection
> feature in firmware for transmitted vif.
>
> Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
>
> Signed-off-by: Karthikeyan Kathirvel <karthikeyan.kathirvel@xxxxxxxxxxxxxxxx>
[...]
> @@ -4964,14 +4994,6 @@ static int ath12k_mac_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
>
> lockdep_assert_wiphy(hw->wiphy);
>
> - /* BIP needs to be done in software */
> - if (key->cipher == WLAN_CIPHER_SUITE_AES_CMAC ||
> - key->cipher == WLAN_CIPHER_SUITE_BIP_GMAC_128 ||
> - key->cipher == WLAN_CIPHER_SUITE_BIP_GMAC_256 ||
> - key->cipher == WLAN_CIPHER_SUITE_BIP_CMAC_256) {
> - return 1;
> - }
> -
> if (key->keyidx > WMI_MAX_KEY_INDEX)
> return -ENOSPC;
>
This hunk seems to break station mode on QCN9274. Maybe on WCN7850 too ? I see
that it was not tested against that HW.
With that hunk I cannot receive broadcast trafic sent by the ap anymore.
Generated by a simple "arping -b X.X.X.X -I br0" in my case.
Replacing that hunk with something similar as what is done in CLO [0] seems to
fix the issue:
@@ -5575,13 +5605,9 @@ static int ath12k_mac_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
lockdep_assert_wiphy(hw->wiphy);
- /* BIP needs to be done in software */
- if (key->cipher == WLAN_CIPHER_SUITE_AES_CMAC ||
- key->cipher == WLAN_CIPHER_SUITE_BIP_GMAC_128 ||
- key->cipher == WLAN_CIPHER_SUITE_BIP_GMAC_256 ||
- key->cipher == WLAN_CIPHER_SUITE_BIP_CMAC_256) {
+ /* IGTK needs to be done in host software */
+ if (key->keyidx == 4 || key->keyidx == 5)
return 1;
- }
if (key->keyidx > WMI_MAX_KEY_INDEX)
return -ENOSPC;
PS: I tested that with firmware PCI WLAN.WBE.1.3.1-00218-QCAHKSWPL_SILICONZ-1
[0] https://git.codelinaro.org/clo/qsdk/oss/system/feeds/wlan-open/-/blob/win.wlan_host_opensource.3.0/patches/ath12k/726-ath12k-add-beacon-protection-support-for-ath12k.patch?ref_type=heads
