This SoC has a single USB 3.1 DRD combo phy and three USB2.0 only
DRD phy controllers as mentined below
* Combo phy supports USB3.1 SSP+(10Gbps) protocol and is backwards
compatible to the USB3.0 SS(5Gbps). 'Add-on USB2.0' phy is added
to support USB2.0 HS(480Mbps), FS(12Mbps) and LS(1.5Mbps) data rates.
These two phys are combined to form a combo phy as mentioned below.
USB30DRD_0 port
+------------------------------------------------------------+
| |
| (combo) USB phy controller |
| +----------------------------------------------+ |
| | USB HSPHY | |
| | (samsung,exynosautov920-usbdrd-combo-hsphy) | |
| +----------------------------------------------+ |
| |
| +--------------------------------------------------+ |
| | USB SSPHY | |
| | (samsung,exynosautov920-usb31drd-combo-ssphy) | |
| +--------------------------------------------------+- |
| |
+------------------------------------------------------------+
| |
| USBDRD30 Link |
| Controller |
+------------------------------------------------------------+
* USB2.0 phy supports only UTMI+ interface. USB2.0DRD phy
is very similar to the existing Exynos850 support in this driver.
USB20DRD_0/1/2 ports
+---------------------------------------------------+
| |
| USB PHY controller |
| +-----------------------------------------+ |
| | USB HSPHY | |
| | (samsung,exynosautov920-usbdrd-phy) | |
| +-----------------------------------------+ |
| |
+---------------------------------------------------+
| |
| USBDRD20_* Link |
| Controller |
| |
+---------------------------------------------------+
The "USB20 phy output isolation" is shared across the USB20 phys.
We have to bypass isolation when any one of the USBs is configured
and enable it when all are turned off. The "USB31 phy isolation"
is seperate for USB31 phy.
This patchset only supports device mode and same is verified with
as NCM device
changelog
----------
Changes in v7:
- added fixes for driver build warnings
link for v6: https://lore.kernel.org/linux-phy/20250821073703.2498302-1-pritam.sutar@xxxxxxxxxxx/
Changes in v6:
- added else part for new supplies in schemas those are only
supported for exynosautov920.
- addressed comments for driver given in v5.
link for v5: https://lore.kernel.org/linux-phy/20250805115216.3798121-1-pritam.sutar@xxxxxxxxxxx/
Changes in v5:
- significant changes were added in v4, removed "Reviewed-by" tag.
- addressed comments from v4 patchset.
- patch (1/6)
- DTS style is corrected and added required supplies in code/schema.
- schema block added to resolve below failure during 'dtbs_check'.
Unevaluated properties are not allowed ('dvdd075-usb-supply', 'vdd18-usb20-supply', 'vdd33-usb20-supply' were unexpected.
- patch (2/6)
- removed usage_counter(take this later in subsequent patch-sets)
- patch (3/6)
- There are 3 types of the phys in this SoC.
- one is simmilar with exynos850 as mentioned in patch no.1.
- second supports only USB3.1 SSP+ and denoted in patch no 5
- third supports only USB2.0 HS as in patch3.
- hs phy in combo phy is "NOT" same as phy. (in patch no. 1)
- These three phys(usbdrd-phy, combo-hsphy, combo-ssphy) are totally
deferent, "NOT" same, hence added three compatible for three phys.
- patch (5/6)
- Since there are two phys in combo phy, explaination is given
in each patch.
link for v4: https://lore.kernel.org/linux-phy/20250701120706.2219355-1-pritam.sutar@xxxxxxxxxxx/
Changes in v4:
- addressed comments from v3 patchset
- removed dts related patches, to be posted in new patchset.
- added regulator, pmu and power sequences.
- phy isol is shared across USBs, added usage counter to bypass or
enable phy isolation.
- modified schemas with hs and combo phy compatible names
(used "combo" to denote combo phy) and regulators
- modified code to work with binding and unbinding devices/drivers
- added "Reviewed-by" tag.
link for v3: https://lore.kernel.org/linux-phy/20250613055613.866909-1-pritam.sutar@xxxxxxxxxxx/
Changes in v3:
- Updated dt-bindings for USB2.0 only.
- Added dt-bindings for combo phy.
- Added implementation for combo phy (SS and HS phy).
- Added added DTS nodes for all the phys
link for v2: https://lore.kernel.org/linux-phy/20250516102650.2144487-1-pritam.sutar@xxxxxxxxxxx/
Changes in v2:
- Used standard GENMASK() and FIELD_GET() to get the major version
from controller version register.
link for v1: https://lore.kernel.org/linux-phy/20250514134813.380807-1-pritam.sutar@xxxxxxxxxxx/
Pritam Manohar Sutar (6):
dt-bindings: phy: samsung,usb3-drd-phy: add ExynosAutov920 HS phy
compatible
phy: exynos5-usbdrd: support HS phy for ExynosAutov920
dt-bindings: phy: samsung,usb3-drd-phy: add ExynosAutov920 combo hsphy
phy: exynos5-usbdrd: support HS combo phy for ExynosAutov920
dt-bindings: phy: samsung,usb3-drd-phy: add ExynosAutov920 combo ssphy
phy: exynos5-usbdrd: support SS combo phy for ExynosAutov920
.../bindings/phy/samsung,usb3-drd-phy.yaml | 50 ++
drivers/phy/samsung/phy-exynos5-usbdrd.c | 651 ++++++++++++++++++
include/linux/soc/samsung/exynos-regs-pmu.h | 3 +
3 files changed, 704 insertions(+)
--
2.34.1
