On Wed, Aug 20, 2025 at 03:35:36PM -0500, Bjorn Helgaas wrote:
> On Wed, Aug 20, 2025 at 04:10:48PM +0800, Richard Zhu wrote:
> > The CLKREQ# is an open drain, active low signal that is driven low by
> > the card to request reference clock.
> >
> > Since the reference clock may be required by i.MX PCIe host too. To make
> > sure this clock is available even when the CLKREQ# isn't driven low by
> > the card(e.x no card connected), force CLKREQ# override active low for
> > i.MX PCIe host during initialization.
> >
> > The CLKREQ# override can be cleared safely when supports-clkreq is
> > present and PCIe link is up later. Because the CLKREQ# would be driven
> > low by the card in this case.
> >
> > Signed-off-by: Richard Zhu <hongxing.zhu@xxxxxxx>
> > ---
> > drivers/pci/controller/dwc/pci-imx6.c | 35 +++++++++++++++++++++++++++
> > 1 file changed, 35 insertions(+)
> >
> > diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
> > index 80e48746bbaf6..a73632b47e2d3 100644
> > --- a/drivers/pci/controller/dwc/pci-imx6.c
> > +++ b/drivers/pci/controller/dwc/pci-imx6.c
> > @@ -52,6 +52,8 @@
> > #define IMX95_PCIE_REF_CLKEN BIT(23)
> > #define IMX95_PCIE_PHY_CR_PARA_SEL BIT(9)
> > #define IMX95_PCIE_SS_RW_REG_1 0xf4
> > +#define IMX95_PCIE_CLKREQ_OVERRIDE_EN BIT(8)
> > +#define IMX95_PCIE_CLKREQ_OVERRIDE_VAL BIT(9)
> > #define IMX95_PCIE_SYS_AUX_PWR_DET BIT(31)
> >
> > #define IMX95_PE0_GEN_CTRL_1 0x1050
> > @@ -136,6 +138,7 @@ struct imx_pcie_drvdata {
> > int (*enable_ref_clk)(struct imx_pcie *pcie, bool enable);
> > int (*core_reset)(struct imx_pcie *pcie, bool assert);
> > int (*wait_pll_lock)(struct imx_pcie *pcie);
> > + void (*clr_clkreq_override)(struct imx_pcie *pcie);
> > const struct dw_pcie_host_ops *ops;
> > };
> >
> > @@ -149,6 +152,7 @@ struct imx_pcie {
> > struct gpio_desc *reset_gpiod;
> > struct clk_bulk_data *clks;
> > int num_clks;
> > + bool supports_clkreq;
> > struct regmap *iomuxc_gpr;
> > u16 msi_ctrl;
> > u32 controller_id;
> > @@ -267,6 +271,13 @@ static int imx95_pcie_init_phy(struct imx_pcie *imx_pcie)
> > IMX95_PCIE_REF_CLKEN,
> > IMX95_PCIE_REF_CLKEN);
> >
> > + /* Force CLKREQ# low by override */
> > + regmap_update_bits(imx_pcie->iomuxc_gpr,
> > + IMX95_PCIE_SS_RW_REG_1,
> > + IMX95_PCIE_CLKREQ_OVERRIDE_EN |
> > + IMX95_PCIE_CLKREQ_OVERRIDE_VAL,
> > + IMX95_PCIE_CLKREQ_OVERRIDE_EN |
> > + IMX95_PCIE_CLKREQ_OVERRIDE_VAL);
> > return 0;
> > }
> >
> > @@ -1298,6 +1309,18 @@ static void imx_pcie_host_exit(struct dw_pcie_rp *pp)
> > regulator_disable(imx_pcie->vpcie);
> > }
> >
> > +static void imx8mm_pcie_clr_clkreq_override(struct imx_pcie *imx_pcie)
> > +{
> > + imx8mm_pcie_enable_ref_clk(imx_pcie, false);
> > +}
> > +
> > +static void imx95_pcie_clr_clkreq_override(struct imx_pcie *imx_pcie)
> > +{
> > + regmap_update_bits(imx_pcie->iomuxc_gpr, IMX95_PCIE_SS_RW_REG_1,
> > + IMX95_PCIE_CLKREQ_OVERRIDE_EN |
> > + IMX95_PCIE_CLKREQ_OVERRIDE_VAL, 0);
> > +}
> > +
> > static void imx_pcie_host_post_init(struct dw_pcie_rp *pp)
> > {
> > struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> > @@ -1322,6 +1345,12 @@ static void imx_pcie_host_post_init(struct dw_pcie_rp *pp)
> > dw_pcie_writel_dbi(pci, GEN3_RELATED_OFF, val);
> > dw_pcie_dbi_ro_wr_dis(pci);
> > }
> > +
> > + /* Clear CLKREQ# override if supports_clkreq is true and link is up */
> > + if (dw_pcie_link_up(pci) && imx_pcie->supports_clkreq) {
> > + if (imx_pcie->drvdata->clr_clkreq_override)
> > + imx_pcie->drvdata->clr_clkreq_override(imx_pcie);
>
> It seems racy to clear the override when the link is up.
>
> Since it sounds like the i.MX host requires refclock all the time, why
> not keep the override permanently?
It will Lost l1ss support if enable override permanetly. I think other
platform have similar issues (at least dwc controller). Most platform use
m.2 socket, which pull down clk_req by EP side devices.
Only standard PCIe slots, which clkreq have not connect by EP devices
because stardard PCIe slots add #clkreq signal happen recent years (maybe
after miniPCIe slot spec). Some old PCIe devices have not connect it.
Even latest PCIe devices, I saw have jumper in PCIe card to controller
#clkreq.
>
> Obviously it must be ok to keep the override for a while, because
> there is some interval between the link coming up and the call of
> .clr_clkreq_override().
>
> Would something bad happen if we *never* called
> .clr_clkreq_override()?
clock will always running, lost L1SS power save feature.
Frank
>
> Bjorn
