On Thu, Aug 28, 2025 at 01:04:26PM +0530, Krishna Chaitanya Chundru wrote:
> The ELBI registers falls after the DBI space, PARF_SLV_DBI_ELBI register
> gives us the offset from which ELBI starts. So override ELBI with the
> offset from PARF_SLV_DBI_ELBI and cfg win to map these regions.
>
> On root bus, we have only the root port. Any access other than that
> should not go out of the link and should return all F's. Since the iATU
> is configured for the buses which starts after root bus, block the
> transactions starting from function 1 of the root bus to the end of
> the root bus (i.e from dbi_base + 4kb to dbi_base + 1MB) from going
> outside the link through ECAM blocker through PARF registers.
>
> Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@xxxxxxxxxxxxxxxx>
> ---
> drivers/pci/controller/dwc/pcie-qcom.c | 70 ++++++++++++++++++++++++++++++++++
> 1 file changed, 70 insertions(+)
>
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index 5092752de23866ef95036bb3f8fae9bb06e8ea1e..8f3c86c77e2604fd7826083f63b66b4cb62a341d 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -55,6 +55,7 @@
> #define PARF_AXI_MSTR_WR_ADDR_HALT_V2 0x1a8
> #define PARF_Q2A_FLUSH 0x1ac
> #define PARF_LTSSM 0x1b0
> +#define PARF_SLV_DBI_ELBI 0x1b4
> #define PARF_INT_ALL_STATUS 0x224
> #define PARF_INT_ALL_CLEAR 0x228
> #define PARF_INT_ALL_MASK 0x22c
> @@ -64,6 +65,16 @@
> #define PARF_DBI_BASE_ADDR_V2_HI 0x354
> #define PARF_SLV_ADDR_SPACE_SIZE_V2 0x358
> #define PARF_SLV_ADDR_SPACE_SIZE_V2_HI 0x35c
> +#define PARF_BLOCK_SLV_AXI_WR_BASE 0x360
> +#define PARF_BLOCK_SLV_AXI_WR_BASE_HI 0x364
> +#define PARF_BLOCK_SLV_AXI_WR_LIMIT 0x368
> +#define PARF_BLOCK_SLV_AXI_WR_LIMIT_HI 0x36c
> +#define PARF_BLOCK_SLV_AXI_RD_BASE 0x370
> +#define PARF_BLOCK_SLV_AXI_RD_BASE_HI 0x374
> +#define PARF_BLOCK_SLV_AXI_RD_LIMIT 0x378
> +#define PARF_BLOCK_SLV_AXI_RD_LIMIT_HI 0x37c
> +#define PARF_ECAM_BASE 0x380
> +#define PARF_ECAM_BASE_HI 0x384
> #define PARF_NO_SNOOP_OVERRIDE 0x3d4
> #define PARF_ATU_BASE_ADDR 0x634
> #define PARF_ATU_BASE_ADDR_HI 0x638
> @@ -87,6 +98,7 @@
>
> /* PARF_SYS_CTRL register fields */
> #define MAC_PHY_POWERDOWN_IN_P2_D_MUX_EN BIT(29)
> +#define PCIE_ECAM_BLOCKER_EN BIT(26)
> #define MST_WAKEUP_EN BIT(13)
> #define SLV_WAKEUP_EN BIT(12)
> #define MSTR_ACLK_CGC_DIS BIT(10)
> @@ -134,6 +146,9 @@
> /* PARF_LTSSM register fields */
> #define LTSSM_EN BIT(8)
>
> +/* PARF_SLV_DBI_ELBI */
> +#define SLV_DBI_ELBI_ADDR_BASE GENMASK(11, 0)
> +
> /* PARF_INT_ALL_{STATUS/CLEAR/MASK} register fields */
> #define PARF_INT_ALL_LINK_UP BIT(13)
> #define PARF_INT_MSI_DEV_0_7 GENMASK(30, 23)
> @@ -317,6 +332,48 @@ static void qcom_ep_reset_deassert(struct qcom_pcie *pcie)
> qcom_perst_assert(pcie, false);
> }
>
> +static void qcom_pci_config_ecam(struct dw_pcie_rp *pp)
> +{
> + struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> + struct qcom_pcie *pcie = to_qcom_pcie(pci);
> + u64 addr, addr_end;
> + u32 val;
> +
> + /* Set the ECAM base */
> + writel_relaxed(lower_32_bits(pci->dbi_phys_addr), pcie->parf + PARF_ECAM_BASE);
> + writel_relaxed(upper_32_bits(pci->dbi_phys_addr), pcie->parf + PARF_ECAM_BASE_HI);
> +
> + /*
> + * The only device on root bus is the Root Port. Any access to the PCIe
> + * region will go outside the PCIe link. As part of enumeration the PCI
> + * sw can try to read to vendor ID & device ID with different device
> + * number and function number under root bus. As any access other than
> + * root bus, device 0, function 0, should not go out of the link and
> + * should return all F's. Since the iATU is configured for the buses
> + * which starts after root bus, block the transactions starting from
> + * function 1 of the root bus to the end of the root bus (i.e from
> + * dbi_base + 4kb to dbi_base + 1MB) from going outside the link.
> + */
> + addr = pci->dbi_phys_addr + SZ_4K;
> + writel_relaxed(lower_32_bits(addr), pcie->parf + PARF_BLOCK_SLV_AXI_WR_BASE);
> + writel_relaxed(upper_32_bits(addr), pcie->parf + PARF_BLOCK_SLV_AXI_WR_BASE_HI);
> +
> + writel_relaxed(lower_32_bits(addr), pcie->parf + PARF_BLOCK_SLV_AXI_RD_BASE);
> + writel_relaxed(upper_32_bits(addr), pcie->parf + PARF_BLOCK_SLV_AXI_RD_BASE_HI);
> +
> + addr_end = pci->dbi_phys_addr + SZ_1M - 1;
I guess this is an implicit restriction to a single Root Port on the
root bus at bb:00.0, right? So when the qcom IP eventually supports
multiple Root Ports or even a single Root Port at a different
device/function number, this would have to be updated somehow?
No need to change anything here; just making sure I understand what's
going on.
> + writel_relaxed(lower_32_bits(addr_end), pcie->parf + PARF_BLOCK_SLV_AXI_WR_LIMIT);
> + writel_relaxed(upper_32_bits(addr_end), pcie->parf + PARF_BLOCK_SLV_AXI_WR_LIMIT_HI);
> +
> + writel_relaxed(lower_32_bits(addr_end), pcie->parf + PARF_BLOCK_SLV_AXI_RD_LIMIT);
> + writel_relaxed(upper_32_bits(addr_end), pcie->parf + PARF_BLOCK_SLV_AXI_RD_LIMIT_HI);
> +
> + val = readl_relaxed(pcie->parf + PARF_SYS_CTRL);
> + val |= PCIE_ECAM_BLOCKER_EN;
> + writel_relaxed(val, pcie->parf + PARF_SYS_CTRL);
> +}
> +
> static int qcom_pcie_start_link(struct dw_pcie *pci)
> {
> struct qcom_pcie *pcie = to_qcom_pcie(pci);
> @@ -326,6 +383,9 @@ static int qcom_pcie_start_link(struct dw_pcie *pci)
> qcom_pcie_common_set_16gt_lane_margining(pci);
> }
>
> + if (pci->pp.ecam_enabled)
> + qcom_pci_config_ecam(&pci->pp);
> +
> /* Enable Link Training state machine */
> if (pcie->cfg->ops->ltssm_enable)
> pcie->cfg->ops->ltssm_enable(pcie);
> @@ -1314,6 +1374,7 @@ static int qcom_pcie_host_init(struct dw_pcie_rp *pp)
> {
> struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> struct qcom_pcie *pcie = to_qcom_pcie(pci);
> + u16 offset;
> int ret;
>
> qcom_ep_reset_assert(pcie);
> @@ -1322,6 +1383,15 @@ static int qcom_pcie_host_init(struct dw_pcie_rp *pp)
> if (ret)
> return ret;
>
> + if (pp->ecam_enabled) {
> + /*
> + * Override ELBI when ECAM is enabled, as when ECAM
> + * is enabled ELBI moves along with the dbi config space.
> + */
> + offset = FIELD_GET(SLV_DBI_ELBI_ADDR_BASE, readl(pcie->parf + PARF_SLV_DBI_ELBI));
> + pci->elbi_base = pci->dbi_base + offset;
> + }
> +
> ret = qcom_pcie_phy_power_on(pcie);
> if (ret)
> goto err_deinit;
>
> --
> 2.34.1
>
