On Mon, Jun 09, 2025 at 12:34:18PM GMT, Frank Li wrote:
> Add three registers: PCIE_ENDPOINT_TEST_DB_BAR, PCIE_ENDPOINT_TEST_DB_ADDR,
> and PCIE_ENDPOINT_TEST_DB_DATA.
>
> Trigger the doorbell by writing data from PCI_ENDPOINT_TEST_DB_DATA to the
> address provided by PCI_ENDPOINT_TEST_DB_OFFSET and wait for endpoint
> feedback.
>
> Add two command to COMMAND_ENABLE_DOORBELL and COMMAND_DISABLE_DOORBELL
> to enable EP side's doorbell support and avoid compatible problem, which
> host side driver miss-match with endpoint side function driver. See below
> table:
>
> Host side new driver Host side old driver
> EP: new driver S F
> EP: old driver F F
>
> S: If EP side support MSI, 'pci_endpoint_test -f pcie_ep_doorbell' return
> success.
> If EP side doesn't support MSI, the same to 'F'.
>
> F: 'pci_endpoint_test -f pcie_ep_doorbell' return failure, other case as
> usual.
>
> Tested-by: Niklas Cassel <cassel@xxxxxxxxxx>
> Signed-off-by: Frank Li <Frank.Li@xxxxxxx>
> ---
> change from v14 to v16
> - none
>
> Change from v13 to v14
> - update to use pci_endpoint_test -f pcie_ep_doorbell
> - change ioctrl id to fix conflict
>
> Change from v9 to v13
> - none
>
> Change from v8 to v9
> - change PCITEST_DOORBELL to 0xa
>
> Change form v6 to v8
> - none
>
> Change from v5 to v6
> - %s/PCI_ENDPOINT_TEST_DB_ADDR/PCI_ENDPOINT_TEST_DB_OFFSET/g
>
> Change from v4 to v5
> - remove unused varible
> - add irq_type at pci_endpoint_test_doorbell();
>
> change from v3 to v4
> - Add COMMAND_ENABLE_DOORBELL and COMMAND_DISABLE_DOORBELL.
> - Remove new DID requirement.
> ---
> drivers/misc/pci_endpoint_test.c | 82 ++++++++++++++++++++++++++++++++++++++++
> include/uapi/linux/pcitest.h | 1 +
> 2 files changed, 83 insertions(+)
>
> diff --git a/drivers/misc/pci_endpoint_test.c b/drivers/misc/pci_endpoint_test.c
> index c4e5e2c977be2..0f3af7adea107 100644
> --- a/drivers/misc/pci_endpoint_test.c
> +++ b/drivers/misc/pci_endpoint_test.c
> @@ -37,6 +37,8 @@
> #define COMMAND_READ BIT(3)
> #define COMMAND_WRITE BIT(4)
> #define COMMAND_COPY BIT(5)
> +#define COMMAND_ENABLE_DOORBELL BIT(6)
> +#define COMMAND_DISABLE_DOORBELL BIT(7)
>
> #define PCI_ENDPOINT_TEST_STATUS 0x8
> #define STATUS_READ_SUCCESS BIT(0)
> @@ -48,6 +50,11 @@
> #define STATUS_IRQ_RAISED BIT(6)
> #define STATUS_SRC_ADDR_INVALID BIT(7)
> #define STATUS_DST_ADDR_INVALID BIT(8)
> +#define STATUS_DOORBELL_SUCCESS BIT(9)
> +#define STATUS_DOORBELL_ENABLE_SUCCESS BIT(10)
> +#define STATUS_DOORBELL_ENABLE_FAIL BIT(11)
> +#define STATUS_DOORBELL_DISABLE_SUCCESS BIT(12)
> +#define STATUS_DOORBELL_DISABLE_FAIL BIT(13)
>
> #define PCI_ENDPOINT_TEST_LOWER_SRC_ADDR 0x0c
> #define PCI_ENDPOINT_TEST_UPPER_SRC_ADDR 0x10
> @@ -62,6 +69,7 @@
> #define PCI_ENDPOINT_TEST_IRQ_NUMBER 0x28
>
> #define PCI_ENDPOINT_TEST_FLAGS 0x2c
> +
> #define FLAG_USE_DMA BIT(0)
>
> #define PCI_ENDPOINT_TEST_CAPS 0x30
> @@ -70,6 +78,10 @@
> #define CAP_MSIX BIT(2)
> #define CAP_INTX BIT(3)
>
> +#define PCI_ENDPOINT_TEST_DB_BAR 0x34
> +#define PCI_ENDPOINT_TEST_DB_OFFSET 0x38
> +#define PCI_ENDPOINT_TEST_DB_DATA 0x3c
> +
> #define PCI_DEVICE_ID_TI_AM654 0xb00c
> #define PCI_DEVICE_ID_TI_J7200 0xb00f
> #define PCI_DEVICE_ID_TI_AM64 0xb010
> @@ -100,6 +112,7 @@ enum pci_barno {
> BAR_3,
> BAR_4,
> BAR_5,
> + NO_BAR = -1,
> };
>
> struct pci_endpoint_test {
> @@ -841,6 +854,72 @@ static int pci_endpoint_test_set_irq(struct pci_endpoint_test *test,
> return 0;
> }
>
> +static int pci_endpoint_test_doorbell(struct pci_endpoint_test *test)
> +{
> + struct pci_dev *pdev = test->pdev;
> + struct device *dev = &pdev->dev;
> + int irq_type = test->irq_type;
> + enum pci_barno bar;
> + u32 data, status;
> + u32 addr;
> +
> + if (irq_type < PCITEST_IRQ_TYPE_INTX ||
> + irq_type > PCITEST_IRQ_TYPE_MSIX) {
> + dev_err(dev, "Invalid IRQ type option\n");
'Invalid IRQ type\n'
> + return -EINVAL;
> + }
> +
> + pci_endpoint_test_writel(test, PCI_ENDPOINT_TEST_IRQ_TYPE, irq_type);
> + pci_endpoint_test_writel(test, PCI_ENDPOINT_TEST_IRQ_NUMBER, 1);
> + pci_endpoint_test_writel(test, PCI_ENDPOINT_TEST_COMMAND,
> + COMMAND_ENABLE_DOORBELL);
> +
> + wait_for_completion_timeout(&test->irq_raised, msecs_to_jiffies(1000));
You should check for the timeout here and below.
> +
> + status = pci_endpoint_test_readl(test, PCI_ENDPOINT_TEST_STATUS);
> + if (status & STATUS_DOORBELL_ENABLE_FAIL) {
> + dev_err(dev, "Failed to enable doorbell\n");
> + return -EINVAL;
> + }
> +
> + data = pci_endpoint_test_readl(test, PCI_ENDPOINT_TEST_DB_DATA);
> + addr = pci_endpoint_test_readl(test, PCI_ENDPOINT_TEST_DB_OFFSET);
> + bar = pci_endpoint_test_readl(test, PCI_ENDPOINT_TEST_DB_BAR);
> +
> + pci_endpoint_test_writel(test, PCI_ENDPOINT_TEST_IRQ_TYPE, irq_type);
> + pci_endpoint_test_writel(test, PCI_ENDPOINT_TEST_IRQ_NUMBER, 1);
> +
> + pci_endpoint_test_writel(test, PCI_ENDPOINT_TEST_STATUS, 0);
> +
> + bar = pci_endpoint_test_readl(test, PCI_ENDPOINT_TEST_DB_BAR);
> +
> + writel(data, test->bar[bar] + addr);
> +
> + wait_for_completion_timeout(&test->irq_raised, msecs_to_jiffies(1000));
> +
> + status = pci_endpoint_test_readl(test, PCI_ENDPOINT_TEST_STATUS);
> +
> + if (!(status & STATUS_DOORBELL_SUCCESS))
> + dev_err(dev, "Endpoint have not received Doorbell\n");
'Failed to trigger doorbell in endpoint\n'
- Mani
--
மணிவண்ணன் சதாசிவம்
