Convert the existing text-based DT bindings for Marvell 8897/8997 (sd8897/sd8997) bluetooth devices controller to a YAML schema. While here, bindings for "usb1286,204e" (USB interface) are dropped from the YAML definition as these are currently documented in file: - Documentation/devicetree/bindings/net/btusb.txt Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@xxxxxxxxxxxxx> --- .../bindings/net/marvell,sd8897-bt.yaml | 91 +++++++++++++++++++ .../bindings/net/marvell-bt-8xxx.txt | 83 ----------------- 2 files changed, 91 insertions(+), 83 deletions(-) create mode 100644 Documentation/devicetree/bindings/net/marvell,sd8897-bt.yaml delete mode 100644 Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt diff --git a/Documentation/devicetree/bindings/net/marvell,sd8897-bt.yaml b/Documentation/devicetree/bindings/net/marvell,sd8897-bt.yaml new file mode 100644 index 0000000000000..6539868c08b8a --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell,sd8897-bt.yaml @@ -0,0 +1,91 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/marvell,sd8897-bt.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell 8897/8997 (sd8897/sd8997) bluetooth devices (SDIO) + +maintainers: + - Ariel D'Alessandro <ariel.dalessandro@xxxxxxxxxxxxx> + +properties: + compatible: + enum: + - marvell,sd8897-bt + - marvell,sd8997-bt + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + marvell,cal-data: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: + Calibration data downloaded to the device during initialization. + minItems: 28 + + marvell,wakeup-pin: + $ref: /schemas/types.yaml#/definitions/uint16 + description: + Wakeup pin number of the bluetooth chip. Used by firmware to wakeup host + system. + + marvell,wakeup-gap-ms: + description: + Wakeup latency of the host platform. Required by the chip sleep feature. + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/pinctrl/rockchip.h> + + sdio0 { + #address-cells = <1>; + #size-cells = <0>; + + btmrvl: btmrvl@2 { + compatible = "marvell,sd8897-bt"; + reg = <2>; + interrupt-parent = <&gpio4>; + interrupts = <RK_PD7 IRQ_TYPE_LEVEL_LOW>; + marvell,wakeup-pin = /bits/ 16 <13>; + pinctrl-names = "default"; + pinctrl-0 = <&bt_host_wake_l>; + }; + }; + + mmc3 { + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + + bluetooth: bluetooth@2 { + compatible = "marvell,sd8897-bt"; + reg = <2>; + interrupt-parent = <&pio>; + interrupts = <119 IRQ_TYPE_LEVEL_LOW>; + + marvell,cal-data = /bits/ 8 < + 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02 + 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00 + 0x00 0x00 0xf0 0x00>; + marvell,wakeup-pin = /bits/ 16 <0x0d>; + marvell,wakeup-gap-ms = /bits/ 16 <0x64>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt b/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt deleted file mode 100644 index 957e5e5c2927c..0000000000000 --- a/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt +++ /dev/null @@ -1,83 +0,0 @@ -Marvell 8897/8997 (sd8897/sd8997) bluetooth devices (SDIO or USB based) ------- -The 8997 devices supports multiple interfaces. When used on SDIO interfaces, -the btmrvl driver is used and when used on USB interface, the btusb driver is -used. - -Required properties: - - - compatible : should be one of the following: - * "marvell,sd8897-bt" (for SDIO) - * "marvell,sd8997-bt" (for SDIO) - * "usb1286,204e" (for USB) - -Optional properties: - - - marvell,cal-data: Calibration data downloaded to the device during - initialization. This is an array of 28 values(u8). - This is only applicable to SDIO devices. - - - marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip. - firmware will use the pin to wakeup host system (u16). - - marvell,wakeup-gap-ms: wakeup gap represents wakeup latency of the host - platform. The value will be configured to firmware. This - is needed to work chip's sleep feature as expected (u16). - - interrupt-names: Used only for USB based devices (See below) - - interrupts : specifies the interrupt pin number to the cpu. For SDIO, the - driver will use the first interrupt specified in the interrupt - array. For USB based devices, the driver will use the interrupt - named "wakeup" from the interrupt-names and interrupt arrays. - The driver will request an irq based on this interrupt number. - During system suspend, the irq will be enabled so that the - bluetooth chip can wakeup host platform under certain - conditions. During system resume, the irq will be disabled - to make sure unnecessary interrupt is not received. - -Example: - -IRQ pin 119 is used as system wakeup source interrupt. -wakeup pin 13 and gap 100ms are configured so that firmware can wakeup host -using this device side pin and wakeup latency. - -Example for SDIO device follows (calibration data is also available in -below example). - -&mmc3 { - vmmc-supply = <&wlan_en_reg>; - bus-width = <4>; - cap-power-off-card; - keep-power-in-suspend; - - #address-cells = <1>; - #size-cells = <0>; - btmrvl: bluetooth@2 { - compatible = "marvell,sd8897-bt"; - reg = <2>; - interrupt-parent = <&pio>; - interrupts = <119 IRQ_TYPE_LEVEL_LOW>; - - marvell,cal-data = /bits/ 8 < - 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02 - 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00 - 0x00 0x00 0xf0 0x00>; - marvell,wakeup-pin = /bits/ 16 <0x0d>; - marvell,wakeup-gap-ms = /bits/ 16 <0x64>; - }; -}; - -Example for USB device: - -&usb_host1_ohci { - #address-cells = <1>; - #size-cells = <0>; - - mvl_bt1: bt@1 { - compatible = "usb1286,204e"; - reg = <1>; - interrupt-parent = <&gpio0>; - interrupt-names = "wakeup"; - interrupts = <119 IRQ_TYPE_LEVEL_LOW>; - marvell,wakeup-pin = /bits/ 16 <0x0d>; - marvell,wakeup-gap-ms = /bits/ 16 <0x64>; - }; -}; -- 2.50.1
