Hi Gunter, On 28/08/2025 04:04, Guenter Roeck wrote: > Chis, > > On Fri, Aug 08, 2025 at 03:05:10PM +1200, Chris Packham wrote: >> Add support for the TI INA780 Digital Power Monitor. The INA780 uses >> EZShunt(tm) technology, which means there are fixed LSB conversions for >> a number of fields rather than needing to be calibrated. >> >> Signed-off-by: Chris Packham <chris.packham@xxxxxxxxxxxxxxxxxxx> > Please send me a register dump for the chip so I can add unit test code > for its support by the driver. Sure. I used the following script to dump the registers cat <<EOF | while read addr len; do printf "%2x: " $addr; i2cget -y -f 1 0x40 $addr i $len; done 0x0 2 0x1 2 0x5 2 0x6 2 0x7 2 0x8 3 0x9 5 0xa 5 0xb 2 0xc 2 0xd 2 0xe 3 0xf 2 0x10 2 0x11 2 0x3e 2 EOF On an unconfigured INA780A with no load just after reset 0: 0x00 0x30 1: 0xfb 0x68 5: 0x00 0x00 6: 0x0b 0x00 7: 0x00 0x00 8: 0x00 0x00 0x00 9: 0x00 0x00 0x00 0x00 0x00 a: 0xff 0xff 0xff 0xff 0x5b b: 0x00 0x03 c: 0x7f 0xff d: 0x80 0x00 e: 0x7f 0xff 0xff f: 0x00 0x00 10: 0x7f 0xf0 11: 0xff 0xff 3e: 0x54 0x49 On a INA780A with no load 0: 0x00 0x30 1: 0xfb 0x6a 5: 0x00 0x00 6: 0x0b 0x00 7: 0x00 0x00 8: 0x00 0x00 0x00 9: 0x00 0x00 0x00 0x00 0x00 a: 0xff 0xff 0xff 0xff 0xd8 b: 0x20 0x03 c: 0x7f 0xff d: 0x80 0x00 e: 0x7f 0xff 0xff f: 0x00 0x00 10: 0x7f 0xf0 11: 0xff 0xff 3e: 0x54 0x49 corresponding lm-sensors output ina780-i2c-1-40 Adapter: i2c-0-mux (chan_id 0) in0: 0.00 V (min = +0.00 V, max = +102.40 V) temp1: +22.0 C (high = +255.9 C) power1: 0.00 W (max = 2.06 kW) energy1: 0.00 J curr1: 0.00 A (min = -78.64 A, max = +78.64 On a INA780A with 10V, 4A load 0: 0x00 0x30 1: 0xfb 0x6a 5: 0x0d 0x75 6: 0x0b 0x20 7: 0x06 0x5f 8: 0x01 0x57 0x0a 9: 0x00 0x00 0x03 0x94 0xcd a: 0x00 0x00 0x11 0x4b 0xaa b: 0x20 0x03 c: 0x7f 0xff d: 0x80 0x00 e: 0x7f 0xff 0xff f: 0x00 0x00 10: 0x7f 0xf0 11: 0xff 0xff 3e: 0x54 0x49 corresponding lm-sensors output ina780-i2c-1-40 Adapter: i2c-0-mux (chan_id 0) in0: 10.77 V (min = +0.00 V, max = +102.40 V) temp1: +22.2 C (high = +255.9 C) power1: 42.06 mW (max = 2.06 kW) energy1: 2.80 J curr1: 3.91 A (min = -78.64 A, max = +78.64 A) And for good measure a word-wise dump (same config and load as above) [root@linuxbox ~]# i2cdump -y -f 1 0x40 w 0,8 1,9 2,a 3,b 4,c 5,d 6,e 7,f 00: 3000 6afb ffff ffff ffff 760d 300b 5a06 08: 5501 0000 0000 0320 ff7f 0080 ff7f 0000 10: f07f ffff ffff ffff ffff ffff ffff ffff 18: ffff ffff ffff ffff ffff ffff ffff ffff 20: ffff ffff ffff ffff ffff ffff ffff ffff 28: ffff ffff ffff ffff ffff ffff ffff ffff 30: ffff ffff ffff ffff ffff 0000 ffff ffff 38: ffff ffff ffff ffff ffff ffff 4954 6227 40: 3000 6afb ffff ffff ffff 760d 300b 5a06 48: 5501 0000 0000 0320 ff7f 0080 ff7f 0000 50: f07f ffff ffff ffff ffff ffff ffff ffff 58: ffff ffff ffff ffff ffff ffff ffff ffff 60: ffff ffff ffff ffff ffff ffff ffff ffff 68: ffff ffff ffff ffff ffff ffff ffff ffff 70: ffff ffff ffff ffff ffff 0000 ffff ffff 78: ffff ffff ffff ffff ffff ffff 4954 6227 80: 3000 6afb ffff ffff ffff 760d 300b 5a06 88: 5501 0000 0000 0320 ff7f 0080 ff7f 0000 90: f07f ffff ffff ffff ffff ffff ffff ffff 98: ffff ffff ffff ffff ffff ffff ffff ffff a0: ffff ffff ffff ffff ffff ffff ffff ffff a8: ffff ffff ffff ffff ffff ffff ffff ffff b0: ffff ffff ffff ffff ffff 0000 ffff ffff b8: ffff ffff ffff ffff ffff ffff 4954 6227 c0: 3000 6afb ffff ffff ffff 760d 300b 5a06 c8: 5501 0000 0000 0320 ff7f 0080 ff7f 0000 d0: f07f ffff ffff ffff ffff ffff ffff ffff d8: ffff ffff ffff ffff ffff ffff ffff ffff e0: ffff ffff ffff ffff ffff ffff ffff ffff e8: ffff ffff ffff ffff ffff ffff ffff ffff f0: ffff ffff ffff ffff ffff 0000 ffff ffff f8: ffff ffff ffff ffff ffff ffff 4954 6227
