On 21.08.25 18:54, Lorenzo Stoakes wrote:
On Thu, Aug 21, 2025 at 10:46:18AM -0600, Nico Pache wrote:
Thanks and I"ll have a look, but this series is unmergeable with a broken
default in
/sys/kernel/mm/transparent_hugepage/khugepaged/mthp_max_ptes_none_ratio
sorry.
We need to have a new tunable as far as I can tell. I also find the use of
this PMD-specific value as an arbitrary way of expressing a ratio pretty
gross.
The first thing that comes to mind is that we can pin max_ptes_none to
255 if it exceeds 255. It's worth noting that the issue occurs only
for adjacently enabled mTHP sizes.
No! Presumably the default of 511 (for PMDs with 512 entries) is set for a
reason, arbitrarily changing this to suit a specific case seems crazy no?
We wouldn't be changing it for PMD collapse, just for the new
behavior. At 511, no mTHP collapses would ever occur anyways, unless
you have 2MB disabled and other mTHP sizes enabled. Technically at 511
only the highest enabled order always gets collapsed.
Ive also argued in the past that 511 is a terrible default for
anything other than thp.enabled=always, but that's a whole other can
of worms we dont need to discuss now.
with this cap of 255, the PMD scan/collapse would work as intended,
then in mTHP collapses we would never introduce this undesired
behavior. We've discussed before that this would be a hard problem to
solve without introducing some expensive way of tracking what has
already been through a collapse, and that doesnt even consider what
happens if things change or are unmapped, and rescanning that section
would be helpful. So having a strictly enforced limit of 255 actually
seems like a good idea to me, as it completely avoids the undesired
behavior and does not require the admins to be aware of such an issue.
Another thought similar to what (IIRC) Dev has mentioned before, if we
have max_ptes_none > 255 then we only consider collapses to the
largest enabled order, that way no creep to the largest enabled order
would occur in the first place, and we would get there straight away.
To me one of these two solutions seem sane in the context of what we
are dealing with.
ie)
if order!=HPAGE_PMD_ORDER && khugepaged_max_ptes_none > 255
temp_max_ptes_none = 255;
Oh and my second point, introducing a new tunable to control mTHP
collapse may become exceedingly complex from a tuning and code
management standpoint.
Umm right now you hve a ratio expressed in PTES per mTHP * ((PTEs per PMD) /
PMD) 'except please don't set to the usual default when using mTHP' and it's
currently default-broken.
I'm really not sure how that is simpler than a seprate tunable that can be
expressed as a ratio (e.g. percentage) that actually makes some kind of sense?
I agree that the current tunable wasn't designed for this, but we
tried to come up with something that leverages the tunable we have to
avoid new tunables and added complexity.
And we can make anything workable from a code management point of view by
refactoring/developing appropriately.
What happens if max_ptes_none = 0 and the ratio is 50% - 1 pte
(ideally the max number)? seems like we would be saying we want no new
none pages, but also to allow new none pages. To me that seems equally
broken and more confusing than just taking a scale of the current
number (now with a cap).
The one thing we absolutely cannot have is a default that causes this
'creeping' behaviour. This feels like shipping something that is broken and
alluding to it in the documentation.
I spoke to David off-list and he gave some insight into this and perhaps
some reasonable means of avoiding an additional tunable.
I don't want to rehash what he said as I think it's more productive for him
to reply when he has time but broadly I think how we handle this needs
careful consideration.
To me it's clear that some sense of ratio is just immediately very very
confusing, but then again this interface is already confusing, as with much
of THP.
Anyway I'll let David respond here so we don't loop around before he has a
chance to add his input.
I've been summoned.
As raised in the past, I would initially only support specific values here like
0 : Never collapse with any pte_none/zeropage
511 (HPAGE_PMD_NR - 1) / default : Always collapse, ignoring pte_none/zeropage
Once could also easily support the value 255 (HPAGE_PMD_NR / 2- 1), but not sure
if we have to add that for now.
Because, as raised in the past, I'm afraid nobody on this earth has a clue how
to set this parameter to values different to 0 (don't waste memory with khugepaged)
and 511 (page fault behavior).
If any other value is set, essentially
pr_warn("Unsupported 'max_ptes_none' value for mTHP collapse");
for now and just disable it.
--
Cheers
David / dhildenb
