From: Wensheng Wang <wenswang@xxxxxxxx>
Add support for MPS VR mp2925 and mp2929 controller. This driver exposes
telemetry and limit value readings and writtings.
Signed-off-by: Wensheng Wang <wenswang@xxxxxxxx>
---
Documentation/hwmon/index.rst | 1 +
Documentation/hwmon/mp2925.rst | 151 ++++++++++++++++
MAINTAINERS | 7 +
drivers/hwmon/pmbus/Kconfig | 9 +
drivers/hwmon/pmbus/Makefile | 1 +
drivers/hwmon/pmbus/mp2925.c | 312 +++++++++++++++++++++++++++++++++
6 files changed, 481 insertions(+)
create mode 100644 Documentation/hwmon/mp2925.rst
create mode 100644 drivers/hwmon/pmbus/mp2925.c
diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
index d292a86ac5da..95bcf71ff6d9 100644
--- a/Documentation/hwmon/index.rst
+++ b/Documentation/hwmon/index.rst
@@ -175,6 +175,7 @@ Hardware Monitoring Kernel Drivers
mp2856
mp2888
mp2891
+ mp2925
mp2975
mp2993
mp5023
diff --git a/Documentation/hwmon/mp2925.rst b/Documentation/hwmon/mp2925.rst
new file mode 100644
index 000000000000..63eda215b6cb
--- /dev/null
+++ b/Documentation/hwmon/mp2925.rst
@@ -0,0 +1,151 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver mp2925
+====================
+
+Supported chips:
+
+ * MPS mp2925
+
+ Prefix: 'mp2925'
+
+ * MPS mp2929
+
+ Prefix: 'mp2929'
+
+Author:
+
+ Wensheng Wang <wenswang@xxxxxxxx>
+
+Description
+-----------
+
+This driver implements support for Monolithic Power Systems, Inc. (MPS)
+MP2925 Dual Loop Digital Multi-phase Controller.
+
+Device compliant with:
+
+- PMBus rev 1.3 interface.
+
+The driver exports the following attributes via the 'sysfs' files
+for input voltage:
+
+**in1_input**
+
+**in1_label**
+
+**in1_crit**
+
+**in1_crit_alarm**
+
+**in1_lcrit**
+
+**in1_lcrit_alarm**
+
+**in1_max**
+
+**in1_max_alarm**
+
+**in1_min**
+
+**in1_min_alarm**
+
+The driver provides the following attributes for output voltage:
+
+**in2_input**
+
+**in2_label**
+
+**in2_crit**
+
+**in2_crit_alarm**
+
+**in2_lcrit**
+
+**in2_lcrit_alarm**
+
+**in3_input**
+
+**in3_label**
+
+**in3_crit**
+
+**in3_crit_alarm**
+
+**in3_lcrit**
+
+**in3_lcrit_alarm**
+
+The driver provides the following attributes for input current:
+
+**curr1_input**
+
+**curr1_label**
+
+The driver provides the following attributes for output current:
+
+**curr2_input**
+
+**curr2_label**
+
+**curr2_crit**
+
+**curr2_crit_alarm**
+
+**curr2_max**
+
+**curr2_max_alarm**
+
+**curr3_input**
+
+**curr3_label**
+
+**curr3_crit**
+
+**curr3_crit_alarm**
+
+**curr3_max**
+
+**curr3_max_alarm**
+
+The driver provides the following attributes for input power:
+
+**power1_input**
+
+**power1_label**
+
+**power2_input**
+
+**power2_label**
+
+The driver provides the following attributes for output power:
+
+**power3_input**
+
+**power3_label**
+
+**power4_input**
+
+**power4_label**
+
+The driver provides the following attributes for temperature:
+
+**temp1_input**
+
+**temp1_crit**
+
+**temp1_crit_alarm**
+
+**temp1_max**
+
+**temp1_max_alarm**
+
+**temp2_input**
+
+**temp2_crit**
+
+**temp2_crit_alarm**
+
+**temp2_max**
+
+**temp2_max_alarm**
diff --git a/MAINTAINERS b/MAINTAINERS
index cd7ff55b5d32..6444cf742098 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -17184,6 +17184,13 @@ S: Maintained
F: Documentation/hwmon/mp2891.rst
F: drivers/hwmon/pmbus/mp2891.c
+MPS MP2925 DRIVER
+M: Noah Wang <wenswang@xxxxxxxx>
+L: linux-hwmon@xxxxxxxxxxxxxxx
+S: Maintained
+F: Documentation/hwmon/mp2925.rst
+F: drivers/hwmon/pmbus/mp2925.c
+
MPS MP2993 DRIVER
M: Noah Wang <noahwang.wang@xxxxxxxxxxx>
L: linux-hwmon@xxxxxxxxxxxxxxx
diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index 55e492452ce8..d0e1eb500215 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -391,6 +391,15 @@ config SENSORS_MP2891
This driver can also be built as a module. If so, the module will
be called mp2891.
+config SENSORS_MP2925
+ tristate "MPS MP2925"
+ help
+ If you say yes here you get hardware monitoring support for MPS
+ MP2925 Dual Loop Digital Multi-Phase Controller.
+
+ This driver can also be built as a module. If so, the module will
+ be called mp2925.
+
config SENSORS_MP2975
tristate "MPS MP2975"
help
diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
index 29cd8a3317d2..64c1b03bf47b 100644
--- a/drivers/hwmon/pmbus/Makefile
+++ b/drivers/hwmon/pmbus/Makefile
@@ -39,6 +39,7 @@ obj-$(CONFIG_SENSORS_MAX8688) += max8688.o
obj-$(CONFIG_SENSORS_MP2856) += mp2856.o
obj-$(CONFIG_SENSORS_MP2888) += mp2888.o
obj-$(CONFIG_SENSORS_MP2891) += mp2891.o
+obj-$(CONFIG_SENSORS_MP2925) += mp2925.o
obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
obj-$(CONFIG_SENSORS_MP2993) += mp2993.o
obj-$(CONFIG_SENSORS_MP5023) += mp5023.o
diff --git a/drivers/hwmon/pmbus/mp2925.c b/drivers/hwmon/pmbus/mp2925.c
new file mode 100644
index 000000000000..453995fca3bf
--- /dev/null
+++ b/drivers/hwmon/pmbus/mp2925.c
@@ -0,0 +1,312 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Hardware monitoring driver for MPS Multi-phase Digital VR Controllers(MP2925)
+ */
+
+#include <linux/bitfield.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include "pmbus.h"
+
+/*
+ * Vender specific register MFR_VR_MULTI_CONFIG(0x08).
+ * This register is used to obtain vid scale.
+ */
+#define MFR_VR_MULTI_CONFIG 0x08
+
+#define MP2925_VOUT_DIV 512
+#define MP2925_VOUT_OVUV_UINT 195
+#define MP2925_VOUT_OVUV_DIV 100
+
+#define MP2925_PAGE_NUM 2
+
+#define MP2925_RAIL1_FUNC (PMBUS_HAVE_VIN | PMBUS_HAVE_PIN | \
+ PMBUS_HAVE_VOUT | PMBUS_HAVE_IOUT | \
+ PMBUS_HAVE_POUT | PMBUS_HAVE_TEMP | \
+ PMBUS_HAVE_STATUS_VOUT | \
+ PMBUS_HAVE_STATUS_IOUT | \
+ PMBUS_HAVE_STATUS_TEMP | \
+ PMBUS_HAVE_STATUS_INPUT)
+
+#define MP2925_RAIL2_FUNC (PMBUS_HAVE_PIN | PMBUS_HAVE_VOUT | \
+ PMBUS_HAVE_IOUT | PMBUS_HAVE_POUT | \
+ PMBUS_HAVE_TEMP | PMBUS_HAVE_IIN | \
+ PMBUS_HAVE_STATUS_VOUT | \
+ PMBUS_HAVE_STATUS_IOUT | \
+ PMBUS_HAVE_STATUS_TEMP | \
+ PMBUS_HAVE_STATUS_INPUT)
+
+struct mp2925_data {
+ struct pmbus_driver_info info;
+ int vout_scale[MP2925_PAGE_NUM];
+};
+
+#define to_mp2925_data(x) container_of(x, struct mp2925_data, info)
+
+static u16 mp2925_linear_exp_transfer(u16 word, u16 expect_exponent)
+{
+ s16 exponent, mantissa, target_exponent;
+
+ exponent = ((s16)word) >> 11;
+ mantissa = ((s16)((word & 0x7ff) << 5)) >> 5;
+ target_exponent = (s16)((expect_exponent & 0x1f) << 11) >> 11;
+
+ if (exponent > target_exponent)
+ mantissa = mantissa << (exponent - target_exponent);
+ else
+ mantissa = mantissa >> (target_exponent - exponent);
+
+ return (mantissa & 0x7ff) | ((expect_exponent << 11) & 0xf800);
+}
+
+static int mp2925_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+ int ret;
+
+ switch (reg) {
+ case PMBUS_VOUT_MODE:
+ /*
+ * The MP2925 does not follow standard PMBus protocol completely,
+ * and the calculation of vout in this driver is based on direct
+ * format. As a result, the format of vout is enforced to direct.
+ */
+ ret = PB_VOUT_MODE_DIRECT;
+ break;
+ default:
+ ret = -ENODATA;
+ break;
+ }
+
+ return ret;
+}
+
+static int mp2925_read_word_data(struct i2c_client *client, int page, int phase,
+ int reg)
+{
+ const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+ struct mp2925_data *data = to_mp2925_data(info);
+ int ret;
+
+ switch (reg) {
+ case PMBUS_READ_VOUT:
+ ret = pmbus_read_word_data(client, page, phase, reg);
+ if (ret < 0)
+ return ret;
+
+ ret = DIV_ROUND_CLOSEST((ret & GENMASK(11, 0)) * data->vout_scale[page],
+ MP2925_VOUT_DIV);
+ break;
+ case PMBUS_VOUT_OV_FAULT_LIMIT:
+ case PMBUS_VOUT_UV_FAULT_LIMIT:
+ ret = pmbus_read_word_data(client, page, phase, reg);
+ if (ret < 0)
+ return ret;
+
+ ret = DIV_ROUND_CLOSEST((ret & GENMASK(11, 0)) * MP2925_VOUT_OVUV_UINT,
+ MP2925_VOUT_OVUV_DIV);
+ break;
+ case PMBUS_STATUS_WORD:
+ case PMBUS_READ_VIN:
+ case PMBUS_READ_IOUT:
+ case PMBUS_READ_POUT:
+ case PMBUS_READ_PIN:
+ case PMBUS_READ_IIN:
+ case PMBUS_READ_TEMPERATURE_1:
+ case PMBUS_VIN_OV_FAULT_LIMIT:
+ case PMBUS_VIN_OV_WARN_LIMIT:
+ case PMBUS_VIN_UV_WARN_LIMIT:
+ case PMBUS_VIN_UV_FAULT_LIMIT:
+ case PMBUS_IOUT_OC_FAULT_LIMIT:
+ case PMBUS_IOUT_OC_WARN_LIMIT:
+ case PMBUS_OT_FAULT_LIMIT:
+ case PMBUS_OT_WARN_LIMIT:
+ ret = -ENODATA;
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ return ret;
+}
+
+static int mp2925_write_word_data(struct i2c_client *client, int page, int reg,
+ u16 word)
+{
+ int ret;
+
+ switch (reg) {
+ case PMBUS_VIN_OV_FAULT_LIMIT:
+ case PMBUS_VIN_OV_WARN_LIMIT:
+ case PMBUS_VIN_UV_WARN_LIMIT:
+ case PMBUS_VIN_UV_FAULT_LIMIT:
+ /*
+ * The PMBUS_VIN_OV_FAULT_LIMIT, PMBUS_VIN_OV_WARN_LIMIT,
+ * PMBUS_VIN_UV_WARN_LIMIT and PMBUS_VIN_UV_FAULT_LIMIT
+ * of MP2925 is linear11 format, and the exponent is a
+ * constant value(5'b11100)， so the exponent of word
+ * parameter should be converted to 5'b11100(0x1C).
+ */
+ ret = pmbus_write_word_data(client, page, reg,
+ mp2925_linear_exp_transfer(word, 0x1C));
+ if (ret < 0)
+ return ret;
+ break;
+ case PMBUS_VOUT_OV_FAULT_LIMIT:
+ case PMBUS_VOUT_UV_FAULT_LIMIT:
+ ret = pmbus_write_word_data(client, page, reg,
+ (ret & ~GENMASK(11, 0)) |
+ FIELD_PREP(GENMASK(11, 0),
+ DIV_ROUND_CLOSEST(word * MP2925_VOUT_OVUV_DIV,
+ MP2925_VOUT_OVUV_UINT)));
+ break;
+ case PMBUS_OT_FAULT_LIMIT:
+ case PMBUS_OT_WARN_LIMIT:
+ /*
+ * The PMBUS_OT_FAULT_LIMIT and PMBUS_OT_WARN_LIMIT of
+ * MP2925 is linear11 format, and the exponent is a
+ * constant value(5'b00000), so the exponent of word
+ * parameter should be converted to 5'b00000.
+ */
+ ret = pmbus_write_word_data(client, page, reg,
+ mp2925_linear_exp_transfer(word, 0x00));
+ if (ret < 0)
+ return ret;
+ break;
+ case PMBUS_IOUT_OC_FAULT_LIMIT:
+ case PMBUS_IOUT_OC_WARN_LIMIT:
+ /*
+ * The PMBUS_IOUT_OC_FAULT_LIMIT and PMBUS_IOUT_OC_WARN_LIMIT
+ * of MP2925 is linear11 format, and the exponent is a
+ * can not be changed.
+ */
+ ret = pmbus_read_word_data(client, page, 0xff, reg);
+ if (ret < 0)
+ return ret;
+
+ ret = pmbus_write_word_data(client, page, reg,
+ mp2925_linear_exp_transfer(word,
+ FIELD_GET(GENMASK(15, 11),
+ ret)));
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ return ret;
+}
+
+static int
+mp2925_identify_vout_scale(struct i2c_client *client, struct pmbus_driver_info *info,
+ int page)
+{
+ struct mp2925_data *data = to_mp2925_data(info);
+ int ret;
+
+ ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, page);
+ if (ret < 0)
+ return ret;
+
+ ret = i2c_smbus_read_byte_data(client, PMBUS_VOUT_MODE);
+ if (ret < 0)
+ return ret;
+
+ if (FIELD_GET(GENMASK(5, 5), ret)) {
+ ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE,
+ page == 0 ? 3 : 4);
+ if (ret < 0)
+ return ret;
+
+ ret = i2c_smbus_read_word_data(client, MFR_VR_MULTI_CONFIG);
+ if (ret < 0)
+ return ret;
+
+ if (FIELD_GET(GENMASK(5, 5), ret))
+ data->vout_scale[page] = 2560;
+ else
+ data->vout_scale[page] = 5120;
+ } else if (FIELD_GET(GENMASK(4, 4), ret)) {
+ data->vout_scale[page] = 1;
+ } else {
+ data->vout_scale[page] = 512;
+ }
+
+ return 0;
+}
+
+static int mp2925_identify(struct i2c_client *client, struct pmbus_driver_info *info)
+{
+ int ret;
+
+ ret = mp2925_identify_vout_scale(client, info, 0);
+ if (ret < 0)
+ return ret;
+
+ return mp2925_identify_vout_scale(client, info, 1);
+}
+
+static const struct pmbus_driver_info mp2925_info = {
+ .pages = MP2925_PAGE_NUM,
+ .format[PSC_VOLTAGE_IN] = linear,
+ .format[PSC_CURRENT_IN] = linear,
+ .format[PSC_CURRENT_OUT] = linear,
+ .format[PSC_POWER] = linear,
+ .format[PSC_TEMPERATURE] = linear,
+ .format[PSC_VOLTAGE_OUT] = direct,
+
+ .m[PSC_VOLTAGE_OUT] = 1,
+ .R[PSC_VOLTAGE_OUT] = 3,
+ .b[PSC_VOLTAGE_OUT] = 0,
+
+ .func[0] = MP2925_RAIL1_FUNC,
+ .func[1] = MP2925_RAIL2_FUNC,
+ .read_word_data = mp2925_read_word_data,
+ .read_byte_data = mp2925_read_byte_data,
+ .write_word_data = mp2925_write_word_data,
+ .identify = mp2925_identify,
+};
+
+static int mp2925_probe(struct i2c_client *client)
+{
+ struct mp2925_data *data;
+
+ data = devm_kzalloc(&client->dev, sizeof(struct mp2925_data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ memcpy(&data->info, &mp2925_info, sizeof(mp2925_info));
+
+ return pmbus_do_probe(client, &data->info);
+}
+
+static const struct i2c_device_id mp2925_id[] = {
+ {"mp2925", 0},
+ {"mp2929", 1},
+ {}
+};
+MODULE_DEVICE_TABLE(i2c, mp2925_id);
+
+static const struct of_device_id __maybe_unused mp2925_of_match[] = {
+ {.compatible = "mps,mp2925", .data = (void *)0},
+ {.compatible = "mps,mp2929", .data = (void *)1},
+ {}
+};
+MODULE_DEVICE_TABLE(of, mp2925_of_match);
+
+static struct i2c_driver mp2925_driver = {
+ .driver = {
+ .name = "mp2925",
+ .of_match_table = mp2925_of_match,
+ },
+ .probe = mp2925_probe,
+ .id_table = mp2925_id,
+};
+
+module_i2c_driver(mp2925_driver);
+
+MODULE_AUTHOR("Wensheng Wang <wenswang@xxxxxxxx>");
+MODULE_DESCRIPTION("PMBus driver for MPS MP2925");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS("PMBUS");
--
2.25.1
