On 8/24/2025 11:15 AM, Bjorn Andersson wrote:
On Mon, Aug 18, 2025 at 12:39:21PM +0800, Fange Zhang wrote:
From: Li Liu <quic_lliu6@xxxxxxxxxxx>
Add display MDSS and DSI configuration for QCS615 RIDE board.
QCS615 has a DP port, and DP support will be added in a later patch.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxxxxxxxx>
Signed-off-by: Li Liu <quic_lliu6@xxxxxxxxxxx>
Signed-off-by: Fange Zhang <fange.zhang@xxxxxxxxxxxxxxxx>
Running dtb checker after applying your patch gives me the following:
$ make qcom/qcs615-ride.dtb CHECK_DTBS=1
UPD include/config/kernel.release
HOSTCC scripts/basic/fixdep
SCHEMA Documentation/devicetree/bindings/processed-schema.json
Documentation/devicetree/bindings/net/snps,dwmac.yaml: mac-mode: missing type definition
Documentation/devicetree/bindings/net/nfc/ti,trf7970a.yaml: ti,rx-gain-reduction-db: missing type definition
Documentation/devicetree/bindings/phy/fsl,imx8mq-usb-phy.yaml: fsl,phy-pcs-tx-deemph-3p5db-attenuation-db: missing type definition
DTC [C] arch/arm64/boot/dts/qcom/qcs615-ride.dtb
arch/arm64/boot/dts/qcom/qcs615-ride.dtb: clock-controller@100000: 'clock-names' is a required property
from schema $id: http://devicetree.org/schemas/clock/qcom,qcs615-gcc.yaml#
Taniya is looking at this one.
Got it. Since the patch appears to be accepted, should I still wait for
mm clk version 7?
https://patchwork.kernel.org/project/linux-arm-msm/patch/20250814-qcs615-mm-cpu-dt-v6-v6-1-a06f69928ab5@xxxxxxxxxxxxxxxx/
arch/arm64/boot/dts/qcom/qcs615-ride.dtb: gpio@3e: $nodename:0: 'gpio@3e' does not match '^(pinctrl|pinmux)(@[0-9a-f]+)?$'
from schema $id: http://devicetree.org/schemas/pinctrl/semtech,sx1501q.yaml#
This is from your patch.
got it, will change "gpio@3e" to "pinctrl@3e"
arch/arm64/boot/dts/qcom/qcs615-ride.dtb: bridge@58: 'vdd10-supply' is a required property
from schema $id: http://devicetree.org/schemas/display/bridge/analogix,anx7625.yaml#
This is from your patch.
got it, will add this part like
https://lore.kernel.org/all/20250604071851.1438612-3-quic_amakhija@xxxxxxxxxxx/
@@ -51,6 +51,64 @@ dp_dsi0_connector_in: endpoint {
};
};
+ vreg_12p0: vreg-12p0-regulator {=
...
@@ -338,7 +396,9 @@ bridge@58 {
interrupts-extended = <&io_expander 0
IRQ_TYPE_EDGE_FALLING>;
enable-gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
reset-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
- wakeup-source;
+ vdd10-supply = <&vreg_1p0>;
+ vdd18-supply = <&vreg_1p8>;
+ vdd33-supply = <&vreg_3p0>;
arch/arm64/boot/dts/qcom/qcs615-ride.dtb: bridge@58: 'vdd18-supply' is a required property
from schema $id: http://devicetree.org/schemas/display/bridge/analogix,anx7625.yaml#
This is from your patch.
same as above
arch/arm64/boot/dts/qcom/qcs615-ride.dtb: bridge@58: 'vdd33-supply' is a required property
from schema $id: http://devicetree.org/schemas/display/bridge/analogix,anx7625.yaml#
This is from your patch.
same as above
arch/arm64/boot/dts/qcom/qcs615-ride.dtb: bridge@58: 'wakeup-source' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/bridge/analogix,anx7625.yaml#
This is from your patch.
will remove it
arch/arm64/boot/dts/qcom/qcs615-ride.dtb: phy@ae94400: Unevaluated properties are not allowed ('vdds-supply' was unexpected)
from schema $id: http://devicetree.org/schemas/display/msm/dsi-phy-14nm.yaml#
This is from your patch.
will change "vdds-supply" to "vcca-supply"
Am I missing something? Is there any reason why these 6 new errors
should be added?
Sorry, I missed those parts earlier. I've re-tested and confirmed the
changes. The patch can pass after refine.
Would it be appropriate to send v7 now, or should I wait until the mm
clk v7 is ready?
Regards,
Bjorn
---
arch/arm64/boot/dts/qcom/qcs615-ride.dts | 90 ++++++++++++++++++++++++++++++++
1 file changed, 90 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcs615-ride.dts b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
index 59582d3dc4c49828ef4a0d22a1cbaba715c7ce8c..39c757b66f47579d9bc7cc5c4d703f7af4434df4 100644
--- a/arch/arm64/boot/dts/qcom/qcs615-ride.dts
+++ b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
@@ -39,6 +39,18 @@ xo_board_clk: xo-board-clk {
};
};
+ dp-dsi0-connector {
+ compatible = "dp-connector";
+ label = "DSI0";
+ type = "mini";
+
+ port {
+ dp_dsi0_connector_in: endpoint {
+ remote-endpoint = <&dsi2dp_bridge_out>;
+ };
+ };
+ };
+
vreg_conn_1p8: regulator-conn-1p8 {
compatible = "regulator-fixed";
regulator-name = "vreg_conn_1p8";
@@ -294,6 +306,84 @@ &gcc {
<&sleep_clk>;
};
+&i2c2 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ io_expander: gpio@3e {
+ compatible = "semtech,sx1509q";
+ reg = <0x3e>;
+ interrupts-extended = <&tlmm 58 IRQ_TYPE_EDGE_FALLING>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ semtech,probe-reset;
+ };
+
+ i2c-mux@77 {
+ compatible = "nxp,pca9542";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bridge@58 {
+ compatible = "analogix,anx7625";
+ reg = <0x58>;
+ interrupts-extended = <&io_expander 0 IRQ_TYPE_EDGE_FALLING>;
+ enable-gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ dsi2dp_bridge_in: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ dsi2dp_bridge_out: endpoint {
+ remote-endpoint = <&dp_dsi0_connector_in>;
+ };
+ };
+ };
+ };
+ };
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&vreg_l11a>;
+ status = "okay";
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <&dsi2dp_bridge_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+ vdds-supply = <&vreg_l5a>;
+ status = "okay";
+};
+
&pcie {
perst-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>;
wake-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
--
2.34.1
