[PATCH 8/9] arm64: dts: mediatek: mt8183-kukui: Fix pull-down/up-adv values

[Julien Massot <julien.massot@xxxxxxxxxxxxx>]

The properties `mediatek,pull-up-adv` and `mediatek,pull-down-adv`
were using incorrect values like `<10>` and `<01>`. These values
are parsed as decimal (10 and 1 respectively), not binary.

However, the driver interprets these as bitfields:
  - BIT(0): R0
  - BIT(1): R1

So valid values are:
  - 0 => no pull
  - 1 => enable R0
  - 2 => enable R1
  - 3 => enable R0 + R1

Using `<10>` is invalid as it exceeds the accepted range.
It was likely intended as binary `0b10` (i.e., `2`),
to enable R1 only.

This patch replaces incorrect values with the correct ones
and removes the leading zero from `<01>` to avoid confusion
with bitfield notation.

Signed-off-by: Julien Massot <julien.massot@xxxxxxxxxxxxx>
---
 arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
index 400c61d1103561db6ee0fb2d2e1c157529d03206..02bdfdb8e53c87dba0ba0024e0c69fcee825552b 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
@@ -574,19 +574,19 @@ pins-cmd-dat {
 				 <PINMUX_GPIO122__FUNC_MSDC0_CMD>;
 			input-enable;
 			drive-strength = <MTK_DRIVE_14mA>;
-			mediatek,pull-up-adv = <01>;
+			mediatek,pull-up-adv = <1>;
 		};
 
 		pins-clk {
 			pinmux = <PINMUX_GPIO124__FUNC_MSDC0_CLK>;
 			drive-strength = <MTK_DRIVE_14mA>;
-			mediatek,pull-down-adv = <10>;
+			mediatek,pull-down-adv = <2>;
 		};
 
 		pins-rst {
 			pinmux = <PINMUX_GPIO133__FUNC_MSDC0_RSTB>;
 			drive-strength = <MTK_DRIVE_14mA>;
-			mediatek,pull-down-adv = <01>;
+			mediatek,pull-down-adv = <1>;
 		};
 	};
 
@@ -603,25 +603,25 @@ pins-cmd-dat {
 				 <PINMUX_GPIO122__FUNC_MSDC0_CMD>;
 			input-enable;
 			drive-strength = <MTK_DRIVE_14mA>;
-			mediatek,pull-up-adv = <01>;
+			mediatek,pull-up-adv = <1>;
 		};
 
 		pins-clk {
 			pinmux = <PINMUX_GPIO124__FUNC_MSDC0_CLK>;
 			drive-strength = <MTK_DRIVE_14mA>;
-			mediatek,pull-down-adv = <10>;
+			mediatek,pull-down-adv = <2>;
 		};
 
 		pins-ds {
 			pinmux = <PINMUX_GPIO131__FUNC_MSDC0_DSL>;
 			drive-strength = <MTK_DRIVE_14mA>;
-			mediatek,pull-down-adv = <10>;
+			mediatek,pull-down-adv = <2>;
 		};
 
 		pins-rst {
 			pinmux = <PINMUX_GPIO133__FUNC_MSDC0_RSTB>;
 			drive-strength = <MTK_DRIVE_14mA>;
-			mediatek,pull-up-adv = <01>;
+			mediatek,pull-up-adv = <1>;
 		};
 	};
 
@@ -633,13 +633,13 @@ pins-cmd-dat {
 				 <PINMUX_GPIO33__FUNC_MSDC1_DAT2>,
 				 <PINMUX_GPIO30__FUNC_MSDC1_DAT3>;
 			input-enable;
-			mediatek,pull-up-adv = <10>;
+			mediatek,pull-up-adv = <2>;
 		};
 
 		pins-clk {
 			pinmux = <PINMUX_GPIO29__FUNC_MSDC1_CLK>;
 			input-enable;
-			mediatek,pull-down-adv = <10>;
+			mediatek,pull-down-adv = <2>;
 		};
 	};
 
@@ -652,13 +652,13 @@ pins-cmd-dat {
 				 <PINMUX_GPIO30__FUNC_MSDC1_DAT3>;
 			drive-strength = <6>;
 			input-enable;
-			mediatek,pull-up-adv = <10>;
+			mediatek,pull-up-adv = <2>;
 		};
 
 		pins-clk {
 			pinmux = <PINMUX_GPIO29__FUNC_MSDC1_CLK>;
 			drive-strength = <8>;
-			mediatek,pull-down-adv = <10>;
+			mediatek,pull-down-adv = <2>;
 			input-enable;
 		};
 	};

-- 
2.50.1